The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support Fuel Injector Clinic
Please Support ExtremePSI

JM Fab Street vs. race. Street numbers

This site may earn a commission from merchant
affiliate links, including eBay, Amazon, and others.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

dwdsm

15+ Year Contributor
564
27
Apr 28, 2005
Scenery Hill, Pennsylvania
I was thinking of going for the street version of the JM fab manifold. I can't find any numbers on the street version. I talked to Jim at JM and he advised the drag version at first but when considering the type of mid power I want and the all around car that I expect mine to be we settled on the street version. I just wanted to see if there are any numbers out there. If not come this spring I will have some. I also don't want to wish I had gotten the drag version either. Any imput is welcome.. Here are my mods. I drag and autocross (I just like to race!) if anyone was wondering..

Bolt on Mods
Evo intake
SBR front mount intercooler
Greddy type RS BOV
60mm TB
Comp "272" cams
SBR Tublar manifold
Turbo Smart wastegate
Magnus heat gasket
B&M short throw shifter
Shep stage 3 tranny
SBR tubular O2 housing
RSR 3" catless exhaust
6an fuel line
Walbro 255 Fuel pump
Razo weighted shift knob
DSM Link


Engine
6-bolt swap
Pauter rods
PTE 5031 Dual BB turbo
Ross Pistons 8.5:1
rebuilt head
3G lifters
FIC 850 injectors
ARP rod bolts
ARP head studs


Performance
396Horse power
350 ft. Lbs. Tourque
On DynoJet
90 Degree day on 93 octane
Best pass 1/4
11.8 @ 116 mph
1.6 60ft
 
JMF told me the street version would be a worth while upgrade on a evoIII powered car...

I would go with the streer version, everyone is on the big donkey dick bandwagon nowa days...

Match you setup, you said you like to drag and auto cross? So having a fat power ban is key to a daul purpose car

But anyways, how do you like the BB 50?


Your setup looks to be properly tuned, so your imput would be reliable...
 
Love the bb 50trim. It puts me right where I want to be. Talked to Jim again and ordered the street version. I agree a matched setup is more important then a super big 4 inch stainless donkey...You get the point. I'll show some numbers this spring when I get back on the dyno.
 
when you dynoed your car,how many lbs were you pushing?
 
24 lbs. of boost on pump. I had to turn it to 22-23 on the street due to some knock. So I am probally 8-16 awhp less then my dyno readout. I am going for a better tune when I get rid of this stupid boost controller. Also going to try not to dyno on a 95 degree day! It hits 18LBS. hard then creeps to my setting. I think the passage is to small to let enough air through to slam the external gate open. Also adding a JMF street mani (ordered).
11.50's here I come...
 
24 lbs. of boost on pump. I had to turn it to 22-23 on the street due to some knock. So I am probally 8-16 awhp less then my dyno readout. I am going for a better tune when I get rid of this stupid boost controller. Also going to try not to dyno on a 95 degree day! It hits 18LBS. hard then creeps to my setting. I think the passage is to small to let enough air through to slam the external gate open. Also adding a JMF street mani (ordered).
11.50's here I come...

Are those your current or new dyno numbers in your sig? You should do a dyno graph comparison of each set if you can..

To show others how much HP the street manifold gave you, and also dyno at the same PSI ish..

Thats if you can, it would help out others when looking to select parts etc
 
Numbers are current. So I will do that. I am adding a aluminum driveshaft and the JMF manifold. Driveshaft will only make the curve a tad different. To be different I am getting the mani powder coated black..Thought you may like that no bling factor. Boost will be a tad less. I am switching to a Tial and running the 23.20lb spring (2 springs actually).
 
Nope just a 1G intake manifold. Ohh I have an Evo Filter and adapter plate going to the 2G MAS...That's all. I can't give up some logs untill I get my power plug back from a friends house.
-Dave
 
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned

Latest posts

Build Thread Updates

Vendor Updates

Latest Classifieds

Back
Top