The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

  • Join the Community!

    DSMtuners is a massive archive of DSM information - but more importantly, it's a COMMUNITY! Join in and participate with other DSMers, and invite all of your DSM friends to make this place their home. Chat with others, create a build thread, post questions and answers. Get involved! Logging in will also remove many of the advertisements, along with this notice. ;) It will also allow you to view images in threads.

Please Support Feal Suspension
Please Support VR-Speed Factory

Articles: Engine & Fuel

Member-submitted articles related to DSM engine and fuel systems.

How to properly install an EWP with Zero issues!!!

Some of you know i switched to a Davies Craig EWP (electric water pump) not long ago EWP150 to...
Last edited:

Big Pump, Small Fuel Line Tune issue resolution "Bandaid" TEST

This is a diagram for a workaround for cars with Big Pumps and Small Lines (stock) issues. It IS...

2g fuel pump install

I was just randomly looking through here to see if there are any how to installs for a fuel...
Last edited:

1G Anatomy of a 1g Knock Sensor

Since most of the goo had oozed out of my knock sensor, and WE ALL WONDER, whats inside that...

2G FWD fuel pump hanger modification for DW200 pump and STM 6AN - barb fitting

You must be logged in to view this image or video.
You must be logged in to view this image or video.
You must be logged in to view this image or video.

so the...

Timing a 4G63 (my "Special" method)

Timing Belt Install – My “Special” Way

This article is good for any timing job but is...
Last edited:

2G -8AN fuel feed/-6AN return bulkhead install with Evo siphon

Here I'm going to show you how to upgrade your fuel pump housing feed line to -8an...
Last edited:

How to fix your idle surge problem.

In hopes to eliminate many of the posts in regards to an idle issue or "idle surge" I have put...


  • fiav lower throttlebody.jpg
    fiav lower throttlebody.jpg
    94 KB · Views: 15,706

2G How I did a friend's Full-blown dual pump hanger

Just some quick flicks of how I did a single hellcat pump for a friend's 2g. Somewhat down and...


  • IMG_20200928_135137.jpg
    728.4 KB · Views: 40
  • IMG_20200928_161928.jpg
    428.9 KB · Views: 40
  • IMG_20200928_162000.jpg
    474.5 KB · Views: 37
  • IMG_20200928_162722.jpg
    647.1 KB · Views: 37
  • IMG_20200928_165318.jpg
    621.5 KB · Views: 39

DSM Valve Spring Seat Pressure Comparisons

In case you are needing to know spring seat pressures for various DSM valve springs, I compiled...

How To: Install a fuel pressure sensor & log with ECMLink

I'm going to show you how to install a fuel pressure sensor and log it with ECMLink.

First off...
Last edited:

Injector Base Settings from ECMTuning

I am putting this in the Fuel Tech articles as information that is already available on the...


  • Various DSM Injector Base Settings from ECMTuning.docx
    13.1 KB · Views: 39

Bosch 2150 Injector settings

These are the settings that were being run with the set of Bosch 2150 Injectors that I purchased...

FIC 1120 Data Sheet

For Offset Voltages in Link. This is my original FIC 1120 Data sheet for others to use if...
Last edited:

FIC 2150 Data Sheet

For offset voltages in Link. This is my original FIC 2150 data matching sheet for others to use...

Generic Engine Build Spec Sheet

A generic Engine Build Spec Sheet for anyone who needs it.

You must be logged in to view this image or video.


  • Generic Engine Shop Build Sheet Blank Master Copy small2.png
    Generic Engine Shop Build Sheet Blank Master Copy small2.png
    82.2 KB · Views: 55
Last edited:

Fuel Injector Calculators

Some people probably already have some calculators bookmarked, but in case you don't, we have...

2G Walbro 450 install w/ bulkhead fitting

Here I’m going to show you how to install a Walbro 450 fuel pump with an STM bulkhead...
Last edited:

How to replace your throttle cable

1. Remove throttle cable end from throttle plate by turning it clockwise to fully open position...


  • IMG_0170.JPG
    381.4 KB · Views: 180
  • IMG_0171.JPG
    376.3 KB · Views: 164
  • IMG_0174.JPG
    181.3 KB · Views: 159
  • IMG_0175.JPG
    336.4 KB · Views: 170
  • IMG_0176.JPG
    343.7 KB · Views: 163
  • IMG_0177.JPG
    264.7 KB · Views: 160
  • IMG_0178.JPG
    255.8 KB · Views: 163
  • IMG_0179.JPG
    239.3 KB · Views: 167
  • IMG_0182.JPG
    163.2 KB · Views: 158
  • IMG_0183.JPG
    430 KB · Views: 168

2G Full Blown Dual Pump Hanger Modifications

OK, so this article will detail the modifications I made to a Full Blown dual fuel pump hanger...

2G 6 Bolt Timing Cover On The Cheap

I know this topic has been covered before but I wanted to make a video of the quality and...
Last edited:

Fuel Pump Rewire Relay Diagram for DUAL in tank pumps

You must be logged in to view this image or video.

Here is a short write up on how to run DUAL in-tank pumps and...
Last edited:

Fuel Pump Rewire Relay Diagram for single in tank pumps

You must be logged in to view this image or video.

86 is the power for the relay to work
85 is its ground so that the...
Last edited:

Walbro 450 install in 1G AWD

Figured I'd throw up some pics of my recent pump install since I hadn't seen anything specific...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications Raven Fabrication RixRacing RockAuto RTM Racing STM Tuned VR Speed Factory

Build Thread Updates

Vendor Updates

Latest Classifieds