1. Join the Community!

    DSMtuners is a massive archive of DSM information - but more importantly, it's a COMMUNITY! Join in and participate with other DSMers, and invite all of your DSM friends to make this place their home. Chat with others, create a build thread, post questions and answers. Get involved! Logging in will also remove many of the advertisements, along with this notice. ;)

Drag Race Build Kratos

Mitsubishi Eclipse GSX
  • Ownership Status:
    Currently Own
    Turbo Type:
    GT35 Variant
    Transmission Type:
    Build Type:
    • Drag Race
    Morrison Fabrications Consoidated Top Mount
    ETS 6 inch Race I.C
    Tial 50MM B.O.V and 2x 38MM W.G
    Magnus V4 I.M
    Aeromotive Mechanical Fuel Pump
    F.I.C 2150
    Weldon FPR
    Dynatek Arc-2
    300M homemade C.O.P
    Nitrous Dry 50 shot
    GSC S3's
    Kiggly Race Springs
    Kiggly HLA
    Curt Brown ported 2G head
    Curt Brown short block Manley turbo tuffs and custom shearer spec wiseco pistons
    Mods-EMS & Logging:
    AEM Series 2
    Speed Density
    J.B precision
    4 Bolt rear end swap
    DSS Driveshaft
    EFISpecialties TCU
    KSport Kontrol Pro Coil Overs
    EVO VIII Rims 17x8 with 245-40/17's
    RM Front/Rear Way Bar's
    Energy Suspension Full Bushing Kit
    1G Big Brake Swap
    EBC USR slotted rotors F/R
    EBC Greenstuff pads F/R
    B.F.G S.S brake lines
    Jay Racing toe-end eliminator kit
    3 Gen Brake master cylinder
    Bulfab cross member
    Battery Relocation
    Building this car since 2010.
  • 1/4 Mile E/T:
    1/4 Mile MPH:
    1/8 Mile E/T:
    1/8 Mile MPH:
    60' Time:

Share this Item


You must be LOGGED IN to post comments! When you are logged in you will see fewer advertisements.
  1. TeamFury
    I was the same way, I actually had this meth kit for over 2 years before I finally hooked it up and I asked myself "why did I wait so long" for my car I went from 10 degrees up top to 20 @30 P.S.I that was the only change was adding meth and tuning. Every car will be different though, they say you can add a couple degrees but I added 10 with no knock until I started really turning it up but 18 is not bad at all for pump gas. I did start by using the hobb switch and I had no issues but I figured it would be easier to just use link to activate it, very user friendly you can control what load point you want to activate it at instead of guessing, I think it was easy. As long as your base tune is on point choose the load point to actuvate it and adjust the secondary global fuel adjustments until you AFR's are where you want them.
  2. xlevanx
    That's awesome good luck with it. I'm debating on running a meth kit. Easy to set up through link and tuning with it?
  3. TeamFury
    Well 2 months ago after I installed the dynatek arc-2 I got up to 37 P.S.I on pump gas and meth with a M10 nozzle. The dynatek harness had a problem so that's where I stopped. Once I get it back in hopefully this week, waiting on the new kelfords, and I upgraded to a M14 nozzle so I have no clue. My WOT timing was 18 up top which is pretty good for pump gas at them boost levels. Even without the bigger nozzle I could probably go 40+ p.s.i with timing in the low teens. I was seeing roughly 74 lbs/min at that boost level @8K+
  4. xlevanx
    How much boost you plan on running in that bad boy?
  5. TeamFury
    Grazie Omar.
      eps991 likes this.
  6. eps991
    nice car!
      TeamFury likes this.
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Feal Suspension Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications OHM Racing Raven Fabrication RixRacing RockAuto RTM Racing SouthBay Fuel Injectors STM Tuned Track Decals Track Sculptures VR Speed Factory