1. Join the Community!

    DSMtuners is a massive archive of DSM information - but more importantly, it's a COMMUNITY! Join in and participate with other DSMers, and invite all of your DSM friends to make this place their home. Chat with others, create a build thread, post questions and answers. Get involved! Logging in will also remove many of the advertisements, along with this notice. ;)

Street Build 92 Laser RS T

Plymouth Laser RS Turbo
  • Ownership Status:
    Currently Own
    Transmission Type:
    Build Type:
    • Street
    FP HTA68
    Holset WG Actuator (20psi spring)
    Hallman RX MBC
    Evo III Exhaust Manifold
    Hogged out 1g o2 Housing
    3 Inch Rear side exit Exhaust
    ETS 10.5 FMIC
    HamFab 2.5" UICP
    Tial Q 50mm BOV
    S90 TB
    Walbro 450 E85HP
    8an feed
    Brushed Fuel Filter
    FIC 1150cc
    Spooln'up Bolt-on FPR (43psi)
    Nightshift COP
    MSD DIS 4 High Output
    Battery Dropped
    Custom Harness
    Nitrous Express Custom Single Fogger Wet Nitrous Oxide kit w/compact Lightning Solenoids
    Nitrous Express Progressive Controller
    Nitrous Express Dry Shot w/compact Lightning solenoid (momentary)
    Nitrous Express bottle heater/blanket/blow down tube

    Seibon Carbon Hood
    "Black" crystal headlights
    LEDs interior/exterior
    35% tint
    CP Carillo 9:1 "power adder" pistons
    Crower I beam rods
    Kiggly Girdle
    ARP main studs
    Fel Pro Permatorque HG
    ARP L19 Head Studs
    HKS 272s cams w/ARP bolts
    Findanza Cam Gears
    Ferrea 1mm SS valves
    Kiggly Beehive springs
    GSC guides/seals
    FTY billet rear main housing
    Mods-EMS & Logging:
    Ecmlink V3 SD
    ForcedFour 62mm Gear Indicator
    Innovate PSN-1 Wideband/Nitrous Pressure Gauge/Controller
    Aem Trans Temp Gauge
    Am 5 Bar MAP
    GM IAT
    2g TPS
    ForcedFour Smart 75 Shift box taking orders from an OpenSims Racing Billet/Carbon Shift Paddle setup.
    Dave Katz Chipped TCU
    Stock F433A Trans John Deere Hygard
    Kiggly Flexplate
    IPT Restall Converter
    IPT End Clutch
    Translab Shift Kit
    Morrison Fab Shift lever
    Anti-Lag Racing Vented Transtick
    Megan Race Coilovers
    Polyurethane Bushings:
    Full Engine and Trans
    Sway Bar
    Control Arms
    Rear Trailing Arm
    Track Arm

    3g Master Cylinder/JMF billet cap
    2g Twin Piston Front brakes
    Slotted Rotors F&R
    SS Brake lines
    17" Centerline Storm
    Dunlop Direzza ZII Tires
    Ultra 142s? 15x8 5.5BS
    M&H Racemaster 24.5x8.5x15
    Parts Wishlist:
    New turbo setup, darker tint
    Pulled from a field in Bellevue, Ohio circa 2008'? This car was originally built by my brother in law and I in my garage. Shortly after we drove it to Philly on Ethanol in 2009 for the first annual Northeast DSM meet. Epic trip due to lack of E85 stations, but we made the trip. In 2010 he parts the car out due to college and well... DSM. I have a hard time seeing the shell go and pick it up from him for $750 needing a lot... my turn.
  • 1/4 Mile E/T:
    1/4 Mile MPH:
    1/8 Mile E/T:
    1/8 Mile MPH:
    60' Time:
    Timeslip Photo Link:
    Timeslip Details:
    32 psi taper to 28psi
    24.5 M&H slicks
    Summitmotorsports Park
    Dyno HP:
    391 bhp
    Dyno TQ:
    355 lb/ft

Share this Item


You must be LOGGED IN to post comments! When you are logged in you will see fewer advertisements.
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Feal Suspension Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications OHM Racing Raven Fabrication RixRacing RockAuto RTM Racing SouthBay Fuel Injectors STM Tuned Track Decals Track Sculptures VR Speed Factory