TopSpeed - Daily Driver Eagle Talon TSi Build

Posted by TRAYTSi, Dec 15, 2008
Southeast Region DSM - Florida, Georgia, North Carolina, South Carolina, Puerto Rico

  1. TRAYTSi

    TRAYTSi Probationary Member

    Joined:
    Oct 31, 2008
    Posts:
    0
    Likes Received:
    0
    Altanta, Georgia
    Hey guys, I'm not new to the boards. But I am new to owning a DSM.

    Bought this 1990 Eagle Talon TSi about a month or so ago. Customer blew up his car about 1 1/2 years ago and has been sitting on the side of TopSpeed Since. I twisted his arm to give it to me at a good price. And the build started!

    I'd like to thank Shawn here at TopSpeed Inc. for doing everything to this car. A lot of hard work, and effort has been put into this vehicle these last couple weeks and the results were great. And I thank Doug for the 313whp, and 306tq on our Dynojet at TopSpeed Inc. at 17PSI.

    Here are the mods, and upgrades performed.

    Engine:
    - (NEW) Topline Pistons & Rings
    - (NEW) Clevite Bearings
    - (NEW) Rods
    - Polished Crank
    - (NEW) Topline Valvetrain
    - AAM Cleaning of Head & Shortblock
    - AAM Surfacing the Head
    - AAM Balance & Blueprint Rotating Assembly
    - AAM Valvejob
    - (NEW) gasket kit
    - (NEW) Brian Crower 272 Camshafts
    - (NEW)ARP Headstuds
    - All (NEW) Belts
    - Evo 8 Injectors
    - Greddy Bov Recirc.
    - (NEW) NGK BPR8ES Plugs
    - Big 16g Turbocharger
    - Walbro Fuel Pump 255lph
    - Ported Exhaust Manifold
    - (New) Vac Lines etc...
    - HKS Racing Suction Intake



    Transmission / Transfercase

    - (NEW) Fluids all around
    - ACT 6 Puck Clutch Kit
    - ACT Flywheel

    Interior:

    - Boost Gauge
    - Autometer Oil Pressure Gauge
    - Greddy Profec B Electronic Boost Controller
    - Apexi SAFC II

    Here are pictures of the build

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]

    All post up dynochart shortly...
     
    #1
  2. TRAYTSi

    TRAYTSi Probationary Member

    Joined:
    Oct 31, 2008
    Posts:
    0
    Likes Received:
    0
    Altanta, Georgia
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
    #2
  3. toofast82

    toofast82 Proven Member

    Classifieds Rating:
    100%
    Joined:
    Feb 8, 2005
    Posts:
    2,614
    Likes Received:
    7
    Tinley Park, Illinois
    313whp sounds pretty good for a b16g on 17psi! Do you plan on dynoing it at like 23psi or so? Nice Build! Should make a great daily driver with great usable power!
     
    #3
  4. TRAYTSi

    TRAYTSi Probationary Member

    Joined:
    Oct 31, 2008
    Posts:
    0
    Likes Received:
    0
    Altanta, Georgia
    We broke it in on the dyno. We didn't want to push it that much further. In about a thousand miles or so I'm going to hook up an SMC Meth Kit and try to turn it up a little more.

    We will see.
     
    #4
  5. toofast82

    toofast82 Proven Member

    Classifieds Rating:
    100%
    Joined:
    Feb 8, 2005
    Posts:
    2,614
    Likes Received:
    7
    Tinley Park, Illinois
    Should run 12s all day on about 21-22 psi if you drive good! very cost effective build though! i would recommend a custom burnt chip though and add some nice features like stutterbox, fuel cut elim, custom a/f and timing, etc. I can burn the chips, if you're interested pm me.
     
    #5
  6. TRAYTSi

    TRAYTSi Probationary Member

    Joined:
    Oct 31, 2008
    Posts:
    0
    Likes Received:
    0
    Altanta, Georgia
    I'll keep that in mind. I'm just farting around with it really. Not looking to spend much. Just use what I got around the shop for fun.
     
    #6

Share This Page