i know the rear axles are the same for 2g AWD Auto and manual, but what about the fronts?looking at JNZ OEM online catalog
i see the left axle there is four options (auto/manual with and without ABS)
where the right only has two options (with and without ABS)im swaping from manual to auto...
i need a stock bore in good condition where i can just hot tank and glaze hone it and be ready to go, i have a set of wiseco stock bore pistons that i would like to use with it so i needs to be stock bore bought one thats already 20 over i was told it was never bored.
What machine shops do you guys use? I need to get my block hot tanked and honed and some wiesco Pistons and eagle rods balanced alog with my head resurfaced/valve job and the head studs drilled larger to 1/2" for the 6bolt head studs
I just picked up my thrid dsm lol, well I bought it knowing it had rod knock. So I got it home today and dropped the pan and the number two cylinder has no rid bearing left lol so I'm looking for a bottom end for cheap anyone have one laying around?
Or maybe 6 Bolt pistons and rods?
basically as the title states what is the Transmission and transfer case oil Drain/fill plug specs?and where can i order one, i looked on ExtremePSI but found only the Oil pan plug. the nearest Mitsubishi dealer is almost 2 hours away... :(
where can i get some of these "window pads" or what is the proper name for them?(not my photo)
i think mine are worn down to much causing the window to rattle
like the title says any one from Modesto wanna meeet up for a bit so i can try out a window switch? i believe my Drivers side is causing my passengers side window to not function properly.i posted here about it not working...
ok so basically a few months ago, i was driving around parked my car when i got home and the passengers side window would not roll upi pulled the door trim off, used some wire and connected the motor to the battery and rolled the window up, so the motor still infact works, the window rolled...
does anyone here in Fresno have an extra drivers side window switch? i think mine went out.my passengers side window would not roll up a few weeks ago, so i connected the window motor to the battery and it rolled up just fine, i checked all the wiring and it seems ok, the drives window...
how do you guys with 2g's improve your steering response?i really miss my old evo would snap back and forth when i turned the steering wheel.
now i know most of that comes from the closer ratio rack and pinion. but is there anything we can do?i also hate how large our steering wheel is...
has any one here ever had this issue?
i cant seem to get my clutch to not want to drag.i did what jacks videos say as far as adjusting the clutch assembly, and the test where you rev it to 7k, while stoped in 1st gear.i have heard that some times if it is adjusted to far then it can hit...
on a Evo 3 OFH what line comes from the pump?the front or back one?the reason i ask is i would like to know if i can inject some oil back on top of the oil pump. to allow it to build some pressure,(i just replaced the rod bearings)
i can not find out what is causing this, its only when i hit bumpsi have Tein SS coilovers with pillowball mounts, the car came with them so i dont know if its because its not hte stock suspension and thats just how coilovers are or whats upi replaced the upper control arms, replaced the...
ok sooo,
i am getting .50amps draw, i think i should be at like .005amps or something which is causing my battery to go dead really fast.i pulled all the fuses in the car and nothing changed. i pulled the radio/ room lamp on the under hood and it dropped to 0.43then I pulled the 60amp fuse...
i am haveing trouble with my idle, it goes rich then leanthe RPM;'s go up and down as it geos back and forth,i cant get the ICS stablethe motor has 180-180-180-180 compression
cam timing is dead onany idea's
i know that this is ghetto, and not the way to go about itbut i am running hotter then i would like,alot of air is being blocked between my SSAC FMIC and the A/C condensor that needs to go to the radiatori have a Mishimotor radiator, i tryed slim fans but they ended up dieing, so i...
just got back from the track, i ran a best of a 12.33@118im on 91 pump + Methanol injection, a M14 jet
1.844 60ft
5.264 330ft
1/8mile 8.003 @ 92.03Mph
¼ mile 12.336 @ 118.145Mphmods in profilehere is a link to the video!YouTube - 12.3@118 ApexVIII 95 Eclipse GSX Sac...
i thought i read some where that some 2g transmissions are different then others like the early ones,i think it was something where early ones like 95's cant use later like 99? or maybe they were just different?is there any truth to this can some one set this straight lol
so i replaced the alternator(autozone Reman) when i pulled the headand then about a week later i replace the battery tooso the issue iswhen im driving for about 15min the low battery volt light starts blinking, and the volt gauge drops(dsmlink changes the stock boost gauge to volts)...
look at my front o2 volts.my car idles really lean after pulling the head/timing belt and installing 264/272 camsany ideas? i am doing a boost leak right now, and the compressions is 180 for all 4 cyl
i just pulled the head, and there is no oil leaks,how does this look?http://i134.photobucket.com/albums/q94/ApexVIII/GSX/IMG_2150.jpgi just installed meth and i am haveing trouble getting the timing on DSMlink just to the stock locations at 20ish psi,when i should be able to have...
i know you cant see much on the Cyl walls but how does everything else look? 126k on the motor i am doing all the basic maintenance, Tbelt BS belt tensioner, pully, ARP's, OEM MLS HGthere is alot of junk on the valves so im having a valve job done on the head while it is getting resurfaced...
where can i get Ignalls replacement bushings? came with the Ignalls camber kit with the black base which is the -.75 to +1.25. the bushings are worn out so i bought another kit,At the time i did not know that the ones on the car were the -.75 kit so i ordered the +1.25 to +3.00 kit and that...
Im installing a Viper 350HV, and everything else is in and working.i just need to run the two wires for the door locks,
in the kit there is aGreen wire = (-)Lock, (+)Unlock Output
Blue wire = (-) Unlock, (+) Lock Outputfrom what i read i am looking for a brown wire...
just wanted to post some pictures of Tahoe when i wen earlier in December. She made it all the way there and back just fine, with a little compressor surge in higher altitude, but the 1g uncrushed BOV should help thatand on the way back at 76!
anyone else have this problem?i have a 1g bov, that is crushed a little. im gunna try an uncrushed one next timebut i did have this problem in my Evo when i went to Kirkwood one timei am at 8ft above sea level, with about 21/22 vac at idlewhen i got to the resort(4500ft maybe?) i...
does any one have a roof rack installed? i got a thule one with the 400XT Aero foot and i am confused on how it mounts how far it goes up ecti have
fit kit (252)
Short roof adapter
snowboard holders
50lb bars
ectany one have any pictures on how the fit kit goes on the window area? min wants...
i am going to order a timing tensioner soon, i have all the other parts for the timing belt job except thatmy build date is Dec 94, so that makes me a "early" 95 right? so i do need the early 95 tensioner correct?i just dont want to order the wrong one
idk if this is a repostbut just keep looking threw the pages this is insane... i dont know if it is a joke or WTF is wrong but look:tease:ROFL:confused:WTFSpanish "tuner". Enjoy - Mitsubishi Lancer Register Forumalso did i post this in the right section?!?!?!
Who has a Thule Roof rack?what all is needed? i know the Yakama one requires something called a short roof kitbut on the thule web site i cant see if theur kit needs itso far all i have is the
252 roof fit kit, which is just the little pads that go from the towers to the roof its...
I rebuilt a 91 60mm 1g Throttle body to replace my 2g TBi half shaft the throttle blade shaft (in picture thats the front of the TB)i set the TPS to .63 and adjusted the ISC to 30 and learned idle to 140but now when and driving if i gently let of the throttle it will not go to idle...
me and some of my friends are going to Sac on the 18th we wanna see some more DSM's there that dayany one else wanna go?here is the link to the local forum thread
Ok track day!!!! Oct 18th! - NorCal Forums
sooo we all know how much 91 pump sucksim still learning on DSMlink
im on a ported B16g in my 95 2gim only about to get about 19psi and 9* or timing, im at about a 10.4 AFRi am wondering what other 2g guys are getting for peak timing, boost and AFR'sif you have any logs please...
Has anyone tryed to build up the seat bolsters on stock seats?mine are getting kinda worn out and i dont really want "racing" seats but i would liek my stock ones to have larger bolsters to help hold me in betteri am sure i can go get some foam or something and try to rebuild, but i...
well my car died so i jumped it, and now my Greddy turbo timer is reading some kind of a message, it lights up, and it looks like of like a back wards C then a O the a 5 so like C05any ideas? maybe when i jumped it, it fried the TT?EDit: actually it reads out something like a E05 (or E0S)\...
Do any of the Ebay projectors use the stock 9006 style bulb? I have a set of HID's that I am using on my LS1 that I want to put on my dsm, but the proojectors that came on the car are H3 style. Im swaping to a 2gb front end so I need new headlights and I want to use the HIDs
i posted this on dsmlink forums also but there is more people on here so maybe some one here might knowi ordered a 3 bar off ebay with a pig tail, the sensor was like $59 or something, i dont think its a actuall GM one because there is no part number on it,but i installed it and i...
ok so on my old evo, i droped in a 255, its normal to run it on the stock FPR,and i know that the DSM ones you can not do that it will over run it, so my question is, who has tryed this and knows for a fact that it will work or it will not work.i dont even know if it will bolt up, just...