I'm swapping my aftermarket headlamp assemblies for OEM (edit: 2GB) headlamp assemblies.
The socket was previously cut off and replaced.
I need to go back to the (edit: 2GB) OEM socket (wiring harness side)
Anyone know the part number?
ThanksEDIT: Re-opening this thread because I have 2GB...
Just installed ECMLink on a new laptop running Windows 11. The app takes 60 seconds to open. When I click any button in the app it spins and spins but is REALLY slow.I already tried running it as "admin" and in Windows 7 compatibility mode.Have anyone run into this before?
Trying to figure out the easiest way to remove the parking brake cables from the car.
I found this write up: https://www.dsmtuners.com/threads/parking-brake-cable-removal-installation-write-up.325346/
but the photos are missing.
Does anyone have a link where I can see the process in photos or...
My door panel trim fell off when opening the door and several fasteners broke.
I need to replace them. Does anyone know the part number for these?
Are these the right ones?
https://www.ebay.com/itm/313200684342
The diagram below seems to show 2 different types.It appears they are:
MR533775...
I did a head rebuild and pulled the evap equipment. Can't get the car to stay running. It turns over, revs to 3000 rpm and immediately dies. Giving it throttle will keep it alive for a few seconds but the RPMs go wild and it dies again. Log attached.
Got my head back from the machine shop. He stripped a screw and I need to replace it. Marked with yellow dots.Is this the correct one?https://www.extremepsi.com/store/product.php?productid=25617
Getting a P302 code. Injector 2 stops firing sometimes. At a red light it just stops. Sometimes, if I turn off the car and crank it back up, it will work until I hit a red light then stop firing again.Troubleshooting:
1. Swapped 1/2 plugs, wires, injectors. No change.
2. Bench tested injector...
I'm pretty sure I have a major boost leak somewhere because under boost I max out my AEM WB on the rich side at only 10-12 psi and the car misfires like a bucking bronco.I've noticed when I'm sitting at a light in neutral and I step on the brake, the AFR goes lean. Around 16-18 AFR lean. The...
My driver's seat broke and I need a replacement asap. I can't decide between Corbeau A4 or Cipher (any model)
I'm a big guy 6 foot 210 lbs. I'd like something that's comfy on long drives. I don't plan to race.Most importantly, I want sturdy brackets that bolt right in. No modding or cutting...
I'd like to go HID but I don't want to do the work my self. I was wondering if there's a retailer that sells these already done? Looking for new head lights and new HID kit already installed and wired (neat & clean). I've see DSMers selling these on the classified but all the wiring / cutting is...
I have a lower temp thermostat in my car and it keeps the temps around 180-185. I'm using ECMLink coolant offset of 15 degrees to make the ECU think it's warmed up. I'm thinking of going back to an OEM thermostat to get the temps up. Thoughts?
I need FP Manifold (w/ ceramic coating) users to chime in.
Is the coating worth it?
How big of a difference does it make.
Finally, how long does it last before flaking off?
I need an accordion hose 2.5" ID 10-12" long.My IC piping requires a weird bend and I can't make it work without a flexbile hose. I bought a "flexible" Gates Hose but it's extremely stiff and wont bend enough.Anyone know where I can get a "slinky" hose?
One of my (small) exhaust manifold studs broke.
I need to know the dimensions/specs so I can find a single replacement.
Anyone know the size/specs?
Anyone know where I can order just 1 without buying the whole set?Edit: Is this the correct size? M8 X 1.25 X 45mm
Edit: Single stud...
I have an unpainted bumper and would like to fill the fog light holes. I probably need a patch for some strength.I found this video showing the process:but I can't find where to buy those products.Can anyone suggestion alternatives?Anyone have a link saved for a good "how to guide"...
I have the 05/06 Outlander caliper brackets installed with stock dust/splash shield. I've bent it back to accommodate the larger rotors but they flop around and vibrate.Would the Outlander dust shields work?
Are there any other options?Outlander brake swap guys, please chime in.
Anyone have long term experience with the Synapse DV BOV?
I'm looking for an honest review and I see some mixed feelings about it.
Looking to replace my dodge mod 1G BOV which flutters under part throttle.https://www.extremepsi.com/store/product.php?productid=27634&cat=1936&page=1
I searched until my fingers bled and couldn't find a list of Big Brake Swaps for the 2G.
I'm pretty certain I've seen a list somewhere but I can't find it.
Maybe a mod can help point me in the right direction?Here's what I can remember.
1. 3000gt
2. CTS-V
3. Cobra?
4. Outlander (bracket swap...
Getting some crazy bucking under WOT (16 PSI). Log attached. Where to start? (besides a boost leak test)
Should I be going to a different plug and/or gap? Currently running NGK BPR7ES @ 0.025
I installed a SS line from the Master Clyinder to the Slave Cylinder and I've had some strange results.
At the same time I installed a XACT flywheel, ACT street disk, and ACT Pressure Plate. I also rebuild the MC and SC at the same time with non-OEM parts (found a rebuild kit somewhere). The...
Looking to buy a reman alt for a 2G.I've heard some horror stories with AutoZone alts.Which reman brands should I avoid?
What are the good ones?Probably buying from RockAuto (but open to options)
https://www.rockauto.com/catalog/raframecatalog.php?carcode=1205749&parttype=2412
Trying to replace the brushes on my 2G alt. I have the pully & front cover off.Problem: Can't remove the stator & shaft from the rear cover. I tried prying it and it moves about 1/8 inch but binds after that. Is there a trick to this or am I missing something?Bonus: Anyone have a diagram of...
I have a 2.5" to 3" DP and I've been using Vibrant 2 bolt gaskets for the DP.
These ones: http://www.jegs.com/i/Vibrant-Performance/231/1458/10002/-1?parentProductId=But, after they've been removed & reinstalled a few times, then crack and split in 2. I'm not very happy with them. They don't...
Got a Jacks Trans double synchro trans. Less than 1000 miles on it.
Having issues shifting.
While running. Grinding gears. Some times get locked out. 1st & 3rd seem like they are the worst.
With the motor off. Very notchey. Getting locked out of 3rd when shifting 2nd - 3rd but not noticeable...
Built race trans with 500km (310mi), SBC SS-TZ clutch w/ new pressure plate. Stock re-surfaced flywheel 10k ago. Replaced master and slave 20k ago.Slave was bleed a week ago but I will double check.
Master rod is backed out. Relief port is not blocked and fork returns normally.
I will try to...
Looking to buy a 3G timing belt kit for my mom's 2004 Eclipse GS. I'd like to get all OEM parts from mitsu. No chinese knock offs.
Anyone know where I can buy the kit besides the stealership?
Looking for belt & bearings mostly. No water pump needed.
If I can't find an OEM kit at a reasonable...
Replacing/Installing a cometic mls hg. What do I need to know?I used a blade to scrape off the block surface to get rid of what looks like carbon build up or some sort of sealer. Also using a scotch brite pad and a little brake cleaner to clean the surface. Is that enough or do I need to do...
What are my options for a 2G 7 bolt MLS head gasket set? I need it to include:MLS Head Gasket
Valve Stem Seals
Valve Cover Gasket... at a minimum.The Cometic StreetPro Set seems to be for the 1G only.What are my options?
Does this kit work on a 2g 7bolt from a 95.https://www.extremepsi.com/store/product.php?productid=28232Description says 89-94 but I found the same manufacturer part number kit on other sites and they state it'll work for a 2G.
Trying to decide what valve train I should go for. The goal for the car is a DD / Weekend warrior with a 400hp goal. Stock cams for now (maybe upgrade in the future). My machine shop guy is about to rebuild my head. He said he may need to cut the valve seats for 0.5mm oversize valves because the...
Just wondering who everyone likes for head rebuilds. I'm looking to get my head rebuilt as I bent some valves and just wanted to know who you all go to?
So my T-Belt snapped (improper tension) at idle. Bent some valves.The head was rebuilt with aftermarket parts about 30,000 km go.I'd like to do my first head rebuild. Just trying to compile a list of things I need to replace and maybe get some advice for a "head virgin".I obviously need...
MD308086 https://www.extremepsi.com/store/product.php?productid=18426vs
MD308587 https://www.extremepsi.com/store/product.php?productid=21146Are these interchangeable?My motor was built by someone else and they used MD308086.
I'm about to replace it and would like to know if it makes a...
I have Jack's trans in my car. How can I tell if it's the 57 (late) vs 58 (early) 2G tranny without pulling it off the car? Is there an ID number I can use to verify? If not, any visual differences?
What are the my options for budget seats? I heard of people adapting Tiburon seats somewhere on here but I can't find the thread. Any good options for seats from other cars?I'd like to spend under $400 for the pair with adapters and brackets. I was looking at Cipher seats. Any opinions on...
I'm looking for an accordion hose for my BOV recirc. 1-1/4 inside diameter for the 1G BOV dump and 1-3/8 for the intake side. I know I wont be able to find one with different ends so I'll have to adapt it.Does anyone know where I can buy an accordion hose in one of those 2 inside diameters?
I tore off the temp sensor wire plug. The 2 wire one (not the 1 wire)
What are my options?
Do I have to get a replacement plug?
Can I repair the one I have?