Cold rolled 16ga .

Fire wall design, mock up and cut out. Pencils, markers, cardboard tape measure, laser, nibbler,grinder, cleco clips ,madness and guessing. Good times. I still have more to do.

It will have sealed ducting. I went with a pusher to keep the fan away from the exhaust heat and to allow room for a larger turbo down the road.

A custom radiator is going to be built for the car and with how tight the packaging is a full mock up one is being built out of wood. It’s cheap, fast to build and allows me to visualize everything. The lower mounts are going to use locating pins on the bottom of the radiator and two brackets...

Thanks it’s been a journey. Thanks for following!

I plan on getting a few more things from them. They make some really nice oil coolers and they are priced reasonably.

Let see it’s been a while. Well I have my drysump tank now. So let sow of some bling pics first. The tank was built by AH Fabrication . They have top notch service and very rapid turn around. I was super impressed with them!

MCA suspension golds if memory serves me.

I figured you would find there stuff helpful and its easier than my typing it all out. Also you might find somethings at curiosichi.com useful too. https://curiosichi.com/bondage-a-guide-to-bonding-to-carbon-fiber/ It's a new site but some good stuff there.

I'd square out the trailing edge in front of the front tires adding a splitter end fences and front tire deflectors. The simple sides spats deflector would also double as a air damn. Also add diffuser to the bottom. Professional Awesome makes some so you can look at their site and see what I'm...

Lets see. The design and build for the removable radiator and intercooler core support is done. i need to do some clean up and a few things but I'm happy with it. The front diffuser supports where also integrated into rad/IC core support. A receiver hitch style design was used for this. The...

I plan on testing and adding restriction plates in the lines if needed. Also an in-line tsat is an easy solution Also.

Yes it is. You can read his full write up here: https://www.eatonmotorworks.com/blog/dsm/evo-vortex-capsule

Thanks ! After rereading my post I said to myself “damn I sound ungrateful”. So regardless an explanation was needed.

ThThe fender braces where intended to be done by the end of August early September at most. I took off the whole month of August to do the work only find supply shortage on the tubing Used. It took a whole month to get tubing that normally can be had in two days max. So the braces had to be...

Now that i'm out of fender brace hell I can start posting a bit and show you guys some more neat stuff hopefully. Here are a few things I purchased a while back.

That is a wrap. All payed orders have shipped. Thanks, Kevin

7/22/2018 THE LIST IS NOW CLOSED All payed Orders have shipped1.mountain_man Paid 2.AlexGsxCummins Paid 3.BoostedTurtle Paid 4. Sold to another 5.dragonov_elite Paid 6.BatMoWheel2G Paid 7.DGajre777...

First 12 sets have shipped. One set setting here waiting for payment. I hope to have the rest back from the coating this week.

When I dropped off the second batch to my surprise the first batch was ready . I'm going to start packing them tomorrow.

I'll take look tomorrow. I have not used them yet but it's what Tilton recommended.

Eaton Motor Works making cool stuff for me. Check them out. He has skill, talent and commitment. https://www.eatonmotorworks.com/

The last batch of braces will be dropped off at the powder coating company tomorrow.

Took off the this week and have been busy getting these done. I have all the remaining sets welded, and ready for final inspection before I drop them off at the coating shop Monday.

I’ll be shipping the first batch off a soon as I get them in. I’ll be call the company doing the coating today.As for another batch I really think this is last at least from me. We will see if I can find another member Fabricatior to take them over perhaps. Idk

There a lot of way to make or add a swirl pot.

Like this one. https://www.amazon.com/Meziere-WN0071-Inline-Thermostat-Housing/dp/B003NDFEC0I have also seen similar units that have AN fittings or wiggins.

You would need a 6bolt water pipe if your running the oem pump or have an AN fitting come off the oem unit.

You can run an inline tstat or like me a temp controlled electric pump.

Yes the first 13 set where sent off to be coated. Four more set have been built already and I have notched most of the remaining tubes to finish out the orders. We are waiting on a few more sandwich bracket to come in. Several where defective from the laser table which is super rare They are...

Glad to see you making these Paul. Really cool!

So i haven't touched the car since Te group buy for may braces started and every bit of free time I have has gone to making them. I did however pic up another piece to the puzzle. Eaton Motorworks is making bolt on swirl pot that simple put are to die for. Brandon's done previous work for me...

No problem!

I have a bit over half the batch fully welded. Last weekend was a wash. We had torrential rains here. So much (over 13 inches) that my shop actually had about an inch of water in it from flooding. Lucky everything was up off the floor but it took a week to get the shop all dried out. I'm going...

Making progress.

It took just under three weeks for the tubing to come in so that pretty much killed the whole month of August. That being said 13 sets are fitted and jig welded. They just need to be welded on little on the back sides of them. So moving along and sorry for the delay!

I'll need more info on the conversion. I really don't want to have to change a bunch of stuff i've done already.

All the brackets and hardware are here. I'm working on getting the brackets welded up. The tubing is usually is the easy part. Call and pick it up the next day. That is not the case this time. When I called them on the 1st they informed me it would be two weeks min. to get it. Apparently the...

If you would like me to ship them directly to another person I can do that for you. Just let me know what you want to do when the time comes

All the laser cut brackets came in today. I'll start posting updates as things start to move along.

7/22/2018 THE LIST IS NOW CLOSED1.mountain_man Paid 2.AlexGsxCummins Paid 3.BoostedTurtle Paid 4. Sold to another 5.dragonov_elite Paid 6.BatMoWheel2G Paid 7.DGajre777 Paid 8.anthony spatafora...

7/8/2018 THE LIST IS NOW CLOSED1.mountain_man Paid 2.AlexGsxCummins Paid 3.BoostedTurtle 4.sixfourbolt 5.dragonov_elite Paid 6.BatMoWheel2G 7.DGajre777 Paid 8.anthony spatafora Paid 9. ottojung620...

7/5/2018 THE LIST IS NOW CLOSED1.mountain_man Paid 2.AlexGsxCummins Paid 3.BoostedTurtle 4.sixfourbolt 5.dragonov_elite Paid 6.BatMoWheel2G 7.DGajre777 Paid 8.anthony spatafora Paid 9. ottojung620...

Catch can is sold.

I have a used greddy catch can for sale. Could use a polish but in good shape. SOLD Gizzmo shift light bnib 75 shipped oboPayPal [email protected] 830 1193

Hmm lets see if a price drop will help. I want this gone. 125.00 shipped obo

Brand new AEM Twin fire digital ignition Module BNIB 125.00 Shipped OBO.Paypal is [email protected] 208 830 1193Kevin

45 degrees would be to great of an AOA on a rear diffuser.

6/19/2018 THE LIST IS NOW CLOSED1.mountain_man Paid 2.AlexGsxCummins 3.BoostedTurtle 4.sixfourbolt 5.dragonov_elite Paid 6.BatMoWheel2G 7.DGajre777 Paid 8.anthony spatafora Paid 9. ottojung620 10. Aproductions 11. jspot80 12...

I'll update again here in a bit with people who paid. I literally just walked in the door from vacation. Thanks, Kevin