Wow,
I am really sorry I didn’t realize how this sounded.
This was big event and they do this every year here. I didn’t have a grudge race set up. He was racing everyone, farm truck did run his daily driver against others. However, I didn’t make that race. I did make it last year in my RAM50...
Another Dead End. Looking for what injector pins need swapped if I was to install a 95 eprom ecu in a 99? I understand firing order. But what about the injectors. I do not have the ecm link.
Hey, I do still make the decals and right now they are the closest I have been able to make to the OEM. A lot of what I have come from DSM tuner users sending me photos and creating them a decal as close as I could to the photos. So they are not OEM and the term "replica" can be somewhat used...
I think I will just buy the 2.0 tractrix cable and adapter. And start learning. It would be nice to send my ecu to someone to have it flashed and returned. But i haven't found that service.
I am looking for some support. I either need together information on everything needed to flash and log my 1999 gsx using the current Black Box Ecu or find someone to flash a tune in it for me. Can anyone help me out there?
I am running into an issue where I keep getting three codes. Knock sensor, egr, and o2bank one. The knock sensor is my biggest concern. I have replaced it with two known working ones and the fault code comes right back. I tested the volts on pin 78 and I had.
. 01 of a volt. I think I should...
Can anyone tell me where to locate the pin on the ecu for the knock sensor on a 2g dsm. I am super frustrated.
I keep seeing 95-96 on pin 78. What about 97-99? Does it work different?
I need to know if I can temporarily use my back up 16g using a tdo5 turbine wheel into to my turbine housing that has been bored out for the tdo6sl2 wheel? I am ordering new wheels for the 20g that was on the car. I know the whole is larger but will it hurt my back up 16 g?
Hello Everyone,I just wanted to stop by and tell you all I have a chance to race against Farm Truck and Azn coming soon.
The car has to be a true street legal car with no roll cage. Has to run e85/pump gas or diesel.
Has to run full interior and exhaust no full cell is allowed either. This...
I have two good GM Mafs. $35.00 each.I also have the 1G ECM Tuning Cable that Converts GM MAF plug straight to the 1G Factory Plug. For use with Ecm Link V3, This cable cost $85.00 dollars new. I will take $35.00 for it.One Maf is sold. I have one left.
Text 812-821-8700 I only accept PayPal
Is there away to make my methanol tank shut off while my clutch is pushed to the floor?
While I'm trying to launch it kicks on and floods out the car while revving. I want to momentarily disable it. I'm looking for ideas using the clutch switch. I really don't want to flip a switch.
I actually don't know the airflow. I know the HTA 68 7cm flowed 47 pounds a minute. But they used the tdo5h wheel in that turbo. This turbo is going to use the tdo6sl2 9 blade. I'm really excited about the turbo and I'm waiting to try it out. I had the HTA 68 8cm recently on my car and I...
I just wanted to get some thoughts on a turbo I am having built. As far as possible hp and street manners.I am having an Evo 316g machined to accept the extended tip billet 7 blade 20g wheel. I am going to use the 9 blade tdo6sl2 turbine shaft and keep it in a 7cm turbine housing that has...
Update! Checked Tps all is good. I pulled all TCU codes. Only codes found was from unhooking the solenoid pack while running.Reset the TCU. It appears I have had all gears the whole time. What it is doing is when the car goes in any gear 1-3 it actually moves but at any rpm above idle it...
I do not understand step 5. What is 4-1?
What number on voltage meter is no continuity. Is this 0.I'm new to the digital multimeter. You have to explain in very clear numbers and terms.
Well the so called original transmission is in my garage and has the very same number on the bottom. I will mess with the TPS sensor and see if it fixes the issue. But I want to pull the Tcu Codes Using a Multimeter Can anyone help me with that? I looked at plymouthlaser.com it has no write up...
Here is the story.I bought the car 2 weeks ago.What I learned is the currently installed transmission is supposed to be from a 1997 Eagle Talon TsiAWD. The person who owned it before swapped the solenoids. He said when he first installed the Talon transmission it was stuck in first gear...
I took the pan off and checked all the solenoids and found that the red ground wire on the red wire solenoid was not tightened down to the valve body. On The inside of the transmission but it all looked very clean. I found no pieces of metal.
New information found.
I was able to get the original transmission from the car. It also has the w4a33ev-s stamped into the side. However, it does have its vin numbers. It also has w4a32 written on the furthest passenger side. So I looked at this trans in the car and it also has w4a32 on...
Here is a picture after I used aircraft cleaner and a brillo pad.[/URL]Additonal photoshttp://s41.photobucket.com/user/Jameschanley/media/20170121_211644 1_zpscz37jcmo.jpg.html
I have a mystery I need help solving. I have an automatic AWD transmission and it has no numbers scribed into the vin plate on the bell housing. I was able to locate the number W4A33 EV-S on the bottom of the bell housing. I called John at IPT tuning and he said he has never heard of this...
I have an update. I took off the transfer case and it did not have the rear tranny bolt in. I went ahead and replaced this. I unhooked the flexplate and turned the torque converter and it spins very easily. It makes no noise. The transmission appears very clean. The three tranny bolts in the...
Ok here is the update with what I found out. First, it is for sure missing a flex plate bolt. It started making a rattle noise. So I need to find a bolt to put in there.
I am wondering if the person before me even spun the converter in all the way? I also ran a multimeter test to read the codes...
Ok here is the update with what I found out. First, it is for sure missing a flex plate bolt. It started making a rattle noise. So I need to find a bolt to put in there.
I am wondering if the person before me even spun the converter in all the way? I also ran a multimeter test to read the...
Alright I put in another tcu and the problem is the same. I have no forward gears. Just park and reverse. Is there anything I need to check? I can take photos of all the wiring hooked up.Also is the 95-99 automatic all the same?
Hello,I just bought my first 2gen eclipse gsx auto. Here is the issue. The car will only go in reverse with the TCU plugged in.
But when I put into drive it has no other gears they just free rev like it's in neutral. If I unhook the TCU, I then can move the car forward but I have drive and...
I am taking my car to the Dyno at fat house fabrication in Martinsville IN.
I will have the dyno for one hour. I will try to post results on the HTA68 V2.Mods:
Delta Regrind Cams 264/272
750cc RC Injectors
Coolingmist Trunk Mount Water/Methanol kit 390cc injector
Forged .020 - WESCO PISTONS...