Playing around with my new camera. The mileage on the engine is unknown. Been in the car over 10 years now. Car runs fine as is. How bad is this scoring?Cylinder 1Cylinder 12344
Car lost power and started vibrating while driving. Pulled over and checked the wires and noticed it was running only from cylinder 1 and 4. So I figured power transistor. Well while I was there I figured I'd do a few things such as new gaskets, test and clean injectors, new knock sensor and...
Forced Performance are having a sale on their dsm zero.Need opinions on running this in place of my hx40 w/.55 bolt on housing. I have been thinking about switching to a t3 manifold and either the .70 or the .82 t3 housing. Goals are 400-450hp on pump gas 2.0 and 9:1 compression if its...
Just thought I'd share how I repaired my drip moldings since they are no longer available and any used one probably has seen better days. In the past I just did a light sanding and repainted them with plasti dip. Problem with this is you can see the areas where the original rubber has worn away...
https://www.thedrive.com/news/31780/toyota-is-making-all-new-parts-for-your-80s-and-90s-supraNissan and now Toyota are helping out enthusiasts with new parts from the factory. If only Mitsubishi would give a toss about all of us DSMers. We could get window trims, evo 3 gearing, rear diff parts...
Recently removed from my car due to constant issues. Not looking to sell for much but it comes with everything. So if you need parts (a year old o2 sensor, new gauge face, replacement leds, serieral port connector, etc) you are welcome to offer me something for it.It may even work it just...
My car out of nowhere has got a very violent bucking issue during spool up. I've checked for boost leaks but my tester keeps popping off at anything over 20psi. It seems to hold fine when it does stay on. The way the car runs it feels like it has a massive boost leak as its very harsh, but after...
I've seen comparisons of the MTXL vs the older UEGO but not the new X series wideband. Does any one have a recommendation?I'm currently running a MTX-L and it's constantly had issues for 4 years. I've replaced everything other than the gauge itself. So I'll either buy a new one or switch to AEM
Trying to remove the ghetto alarm that was installed before I got the car. I was under the dash and I found 2 items I'm not sure if they are oem or not, just bleeding hard to see up there without some nija yoga skills. So suggestions would be good.-1st pic is the wiring that goes up towards...
Getting close to dialing in my car now, just need some pointers and maybe advice on how to set up my DA tables.This run was using the modified EVO da fuel and timing tables. Boost was at wastegate pressure of 18psi. Its hot out around 90 degrees so my intake temps are high. Im seeing a few...
Took about 2 months but finally got them in. They fit ok but I did had a few issues getting the right mounting brakets and getting them to fit well. All in all not bad for the price.
Can someone take a look at my logs and let me know how they are. My AFRatioEst and MTX-L are now running close to each other but are still off by a little. How close should they be to each other?This is on the new update btw.
Well I can finally drive my car in the day:DNot sure if I should do an emblem for the front or not. Maybe the stock red one or black or nothing?Also the back, should I get a emblem or something?Opinions please.
Just started messing with link. Looking at my idle log it looks like my o2 is shot correct?Also I know AEM UEGO tend to have a accuracy issue but its reading around 14.0.1 on the log but in the car its reading 15.2.1??edit sorry meant to post in log advice section
I am looking to get a new paint job here soon and looking at options. I will not be painting the engine bay so I am thinking to either repaint it factory red or maybe go with a metallic alternative that will still look ok. Not the best picture I know but I cant get anything right now as it has...
Well I finally decided to just go ahead and buy a blanket for my Holset. I ordered from PTP and bought the Subaru one in black.First thing is do not try to contact PTP by PM or by email as they will not respond. The best way to contact them is by phone. They don't have the best online...
I have an issue with my MAP mvs o2 housing fitting my bep HX40 Housing. I bought this thing a long time ago and just now checking fitment and I'm pissed. I didnt notice the small inlet size of the o2 housing. Will this cause major flow issues? I have grinded the most I can out of it and this is...
Just got my new 2G HD pulley and it came with a slight chip on the side. Would this mess up the belt if it was installed?Also the new one looks slightly different than the one that came off, the center section is slightly more indented than the old one. I didnt test fit it yet because im...
I posted in the local forums but got nothing.Im trying to pass emissions but since my car is a 95 it wont qualify for an OBD test, I get the ASM test instead. Since its awd I dont have to have a load test but I have to do 2 speed idle test.I tried one shop and told them that it was...
I just moved to coweta county and I need to get an emission test done.I asked around and no one can do awd testing which is good, but since its a 95 they want to do a ASM test, which I know I will fail. Is there any way I can get put into a OBD test since I have a bloody OBD2:banghead:? Is...
Some say that he also has a blow off valve but it's only heard during mating season...and that hes got it into his head that civics are edible.Stiggy meets a DSM...and a E350
World Cup started today, cant wait for England vs USA game (cmon lions:p)Canadian gran prix weekend is under way (would like to see Mercedes GP compete with Mclaren and Red Bull)
And of course Le mans 24hr will start tomorrow (Audi vs Peugeot??)
A dreaded fuel sending unit fitting questionwell I was trying to remove my fuel sending unit hose to install my STM tank to rail kit. And man is this thing tight. Sprayed it for a day with blaster, I used line wrenches and made sure not to bend the line and brake it. Well the damn thing is...
Just want to rant about a new job I was going to start this coming Tuesday. I had to travel 5 and 1/2 hours to Blairsville Pa in the beginning of this week to interview for a new job. I did two days of interviewing and stayed one night at a hotel. Got back on Wednesday night and I was informed...
ACT 2600 with street disc
New oem TOB
ACT streetlite-correct step
New oem slave
New fork and pivot ball with one shim- fork sits towards the dr side
locktite was used on all bolts and torqued to spec
Small amount of grease was put on the TOB and output shaft
Bled many times
Slave rod...
2010 season looks like it will be interestingI knew shumacher would come back ever since the mid season Massa replacement issue.Button and Hamilton
Schumacher and Rosberg
Massa and Alonso
Vetle and Weber
Plus a US team finally.I just cant wait for schumi, I grew up watching this...
Just driving around town today I saw this. Sorry for the crappy phone quailty but I just saw it in the corner of my eye at the light. The best part...on the back on the dr side it said HEMI and on the pass side it said V12!!!ROFL
Im getting a lot of pressure in my coolant system still and im not sure why. Flushed coolant system, over flow tank is full, then left cap off to get the air out but it keeps on letting air out and will not stop. So I did a compression test and im 176,175,176,180 with no leaking or burning of...
Looking to buy a new suspension setup for my GSX. Daily driven with some trips to the strip and two autoxs a year.Im thinking about running koni yellows up front due to them being the overall best for our cars. I would like to do konis in the rear but the price and the difficulty of...
The contact on my passenger side fuel level indicator looks like its starting to get worn out. Is it possible to solder a metal strip on top of the contact so I get a better connection?
Came out of class today and see my car a little bruised up.lifted 2500 cummins and pretty much ran over the front left sidedamage to
fender
headlight
front bumperOwner has agreed to pay under the table and he seems a nice guy. Where do you guys recommend buying parts? I would go...
Looking to buy a bike this coming spring and just wanted to see what you guys thinkLooking for 600-750cc sport bike
Nothing older than a 98
prefer low miles
Spend no more than $4k
easy to work on
reliablelist
Honda CBR600RR
Yamaha R6
Kawasaki ZX6
Triumph 675 (My dream bike but...
I have installed a 1G throttle body and I am experiencing some idle issues.When starting the car cold the idle does not rise to warm up the car and in fact will run at about 600rpm. It has trouble keeping constant and will sometimes stall when I press the gas then let of. When the car is...
I am looking to install my Koyo so I need to find some space.Is it possible to use the a/c fan (drivers side) in place of the cooling fan? since its much thinner.Then I was thinking of buying this for my a/c fan...
Im running keydriver stage 3 chip so my car has a decent tune, but I wanted to use my SAFC to fine tune it.Installed according to vfaq pageI have everything setup fine, karman, hi and los set to zero, 4cyl arrow up, and all wiring is good.The car will run fine then all of a sudden...
Ok i just put my FIC 650s in and trying to do a basic tune with my AFC and loggermods
EVO3
SSAC FMIC
walbro 190
stock FPR
Apexi AFCI
3' exhaustIm trying to setup my fuel trims using road racing and vfaq guidelinesat 1000rpm my sht trim is at -15 and my lng trim is at 3 (which...
Looks like the new lancer may have a chance to sell well. Guessing you guys have seen the new commercial (think they are over doing their "titanium" paddle shift thing a little too much).http://www.supercars.net/cars/3705.htmlBut looking at its old time rival in a new form...
I'm looking to match my gauge cluster to my autometer ulralite gauges.Ive found
http://cgi.ebay.com/ebaymotors/Reverse-Glow-Gauge-Mitsubishi-Eclipse-95-99-Turbo-97-98_W0QQitemZ280089732149QQihZ018QQcategoryZ43952QQssPageNameZWDVWQQrdZ1QQcmdZViewItem...
Got into a debate with a local "redneck" (sorry if im offending anyone) about what the best engine is for under $10,000.Im talking about buying a used/new engine and rebuilding it to create the most power, torque, reliability, drivability all under 10K?93 octane, nitrous allowed, any...
Almost ready to run my new ebay dp and no cat. Can I leave my o2 sensor in and just remove my CEL everytime it comes on?Or is it best to remove it, plug the hole and rap the sensor in foil?Would think about doing the fix explained in vfaq but I want to leave the wires alone.
has anyone tried this dp?http://cgi.ebay.com/ebaymotors/95-99-ECLIPSE-TALON-GST-TURBO-DOWN-PIPE-DOWNPIPE-96-97_W0QQitemZ290076878384QQihZ019QQcategoryZ33633QQrdZ1QQcmdZViewItemLooks like it replaces the cat altogether, and any one confirm this?I wanti to repalce my stock dp with a...
Ok I have looked on the forums about all the different dataloggers that I can buy.So far http://www.obdloggers.com seems to be the best for $150 shipped.I looked on eBay and the datalogger kit is around the same price. I have heard people buying everything separate and saving a lot of...
I continue to get 2 codes show up on my check engine light.First is knock sensor malfunction. This came on every so often when my car was stock. Now it comes on right after I remove the CEL. I replaced the knock sensor last year. The car itself is running better than ever, smooth idle and...