Does anyone have a DYI ideas for Hood struts for 2G with carbon hood?? A carbon hood is lot lighter so 300m hood struts won’t work or any struts for a big hood. I’m thinking a 15lbs strut but I’m not sure the length.Maybe someone has the right length I would need?The eBay kit(with the red...

3000GT VR4 6 speed J4G LSD diff3.307 gear ratio used for Auto dsm/Evo 7-9(that’s my understanding can be wrong still looking into it)$700US plus shippingAny questions dm me

Magnus Motorsports fuel pump bracket anodized blackcomes with all hardware$550 shipped

2G shifter base with T1 strain gauge when used in conjunction with an engine management system that supports a strain gauge output for powershifting, will help you achieve those lightning quick shifts. This shifter was also re-enforced.I bought this shifter with strain gauge off Boostin...

I have a carbonetics eclipse 2G front bumper no opening and a 4” drag lip just like Boostin performance has on their drag car but made out of carbon. An opening can be made if you want to opened it up to work with your intercooler size. You can make it as big as you want.I just got it from...

Brand New Syvecs S6 GP. Same computer that's in the Magnus Motorsports 2G DSM. I've decided to part out my car and never got to install this.1800$ shipped.Comes with:- THE ECU- Connector- A bunch of extra pins (both big and small pins)- I'll throw the crimper in as well for...

Hey guys anyone have experience with installing the carbonetics rear carbon quarter window deletes? Have the glass off just not sure the best way to install them!!Thinking to use rtv black silicone but before I use that just wondering if someone has s better way?Thanks for your time

Just wondering if anyone knows why this 6bolt oil pan is indented like this?(dirty one with the green block oil drain side) Never seen it like that before. All the pans ive seen or the one I have is flat like the STM pic (drain plug side)Thanks for your help

Hey guys just wondering if anyone has any experience with a 3000gt rear end in a dsm? I’m thinking of putting a 3k rear end in my 2G(yes I know I need a subframe, Axles, driveshaft ect...) One thing I don’t know is what 2nd piece of the driveshaft do I use the smaller one between rear...

Hey does anyone have any pictures of a Carbonetics Drag wing on a 2G? They offer it for a 1G not 2G so I'm guessing its the same wing so I'm just wondering if anyone has pics of it on a 2GThanks

Hey guys I have a set of FIC 1650cc injectors for sale. They are coming back from FIC today cleaned and flow tested. Have the Flow sheet to prove they are cleaned and ready to go.Looking to get $650 shippedWill have pics tonight will post when I have the injectors back. Comes with pig...

Hey tuners, I'm building a drag car and I'm not to sure if I lock up the front or rear with the staging brake. Can anyone help me on how I should plumb it? I am running a Chase Bays Brake Booster Eliminator and its a non ABS 2G. I have a CNC staging break that I got from STM but I didn't get the...

Hi all,Just a very simple question. Would any one be able to tell me the diameter of the screw that holds the wires through the ring terminal on the coil pack itself? To access the screws I am talking about, you would have to remove the protective cover on the ignition coil. See picture...

Hey all,I just did a few upgrades to my fuel system. I added a new intank high pressure pump, an inline Bosch pump as well as upgraded my fuel lines. The charcoal canister was removed a long time ago but the vent tube for the tank (or whatever it's called) always stayed up front in the...

Im looking to wire in the boost solenoid to my AEM ems. If im not mistaken the wires that were coming off my boost solenoid should be going to my original boost solenoid wires. But my original one was removed and I dont know where the original wires are so I was planning to just run it directly...

I'll start with the basics. My car is 98 Talon TSI with a 6bolt and CAS swap. Trying to get my car to run but it will not. When I turn it over, it cranks, fires for a second and shuts off. This is everything I've gone through with it:This is what I've checked while Cranking. 1. Read...

i just got the maft and 3''gm and i would like to know how some cars run with out the stock mas because dont you need to plug that in to it with the big plug that comes with the maft. Sorry about the newbie question.Thanks Mike

I've had some bad things happen to me lately with my car. Just a butt load of bad luck Every week something new comes up. So I'll explain my story.I was driving my car just the other day cruising normally when it starts to sputter, bog, and than finally shuts off. I start it back up and...

First I'll start with the setup and car.This is a 98 Eagle Talon TSI awd, with a 6 bolt swap in it.From what I have found on here from searching, I cannot adjust base timing on my 98 car because I do not have the clip/port to ground out and neutralize the computer from automatically...

Hey,Two quick questions. I'm kinda getting a little mixed up on the first from what I've been reading on here.I have a 98 Turbo Awd DSM. Would any turbo 2G engine harness work, or would I specifically need it from a 98?Also the ECU on the car is cooked. Once again would any 2G ECU...

I was wondering if anyone knew the pin outs for the power transistor? Im looking for specifically which pin fires the 2&3 coil pack/cylinders. Also this is for a Second Gen! Any help would be epreciated!. Thanks!

This car has just been bad luck for me. Problem, after problem.Anyways, after blowing my motor a few months ago, I decided to swap a 1G in. Btw, the car is a 2G Talon. Motor is completely rebuilt.After having some timing belt issues because of a faulty brand new factory tensioner, I...

Hey,My buddy and I are in the process of swapping in a 6 bolt in his 2g Talon. I've noticed many people on here mount their oil coolers behind the bumper on the drivers side infront of the drivers side wheel. When we removed the bumper we found this black box there...

Well tonight we started the block assembly on our six bolt engine.I had a two things I wanted to clarify before I began assembly just to be extra sure.First off, after receiving my block back from my machinist, he mentioned that the main bearings could be placed in any journal and that...

Hi again,I'm going to be installing an upgraded oil cooler. I'm going with the exact same oil cooler setup Mavisky posted in his post (Great write-up btw) here : http://dsmtuners.com/forums/showthread.php?t=220259&highlight=oil+coolerI have a 2g in which I am currently swapping 6-bolt...

Well after a miss-shift, not much was left undamaged on my 7-bolt 4g63. I went ahead and pick up a 6-bolt 4g63 for a complete build up.Current mods: -Forced Performance Green Turbo -Ported exhaust manifold -3" dp and exhaust -port and polished head -Dual valve springs, retainers, and...

Hi,I was wondering if they make a factory service manual for the car? I'm actually talking about one from Mitsubishi, not a crappier one like Chilton, etc... Something in deep description like the Helms manual (For a Honda, yes I'm a Honda owner to, sorry.:coy: ).Thanks.Mike

I just put a 1g head on my 2g block and i need to put a 1g cas on it right. Can anyone tell my does it have to be a turbo one or can it be non-turbo one because i have a non-turbo cas and i would like to know if it would work.Thanks Mike