I have a 1998 gst with aftermarket suspension (KYB + GC) and a RMDSM swaybar and is just slightley lowered with 18in wheels.When I'm driving and I go over any bumps in the road I hear a CLUNK sound come from the front suspension. I believe it is coming from the passenger side. Also when...
Can anyone tell me if the Alpine Type-R Speakers (6.5 components front, and 6x9 rear)will fit in our cars without having to hammer or make a bracket?Alpine Type-R SPR-17S (components)
Alpine Type-R SPR-69C (6x9s)Thanks!
Can someone please clarify the large differences between using an ebay projector headlight assembly with an HID kit installed in it compared to a headlight assembly with somthing like a BMW projector housing and HID kit installed. I've heard that the cutoff gets distorted when you use the ebay...
Im looking for a set of new headlights because my stock ones fogged up on me. I would like to purchase a clean looking set of projectors that look as stock as possible. I was looking at this style right hereHave you seen any similar to this or even the same at a good price?thanx
My clutch just recently started doing this. When i drive the car for a while (a few days) the clutch hydrolic system seems to build pressure, enough to where it changes the point of engagement of my clutch to where if i barley press in the clutch (1inch) it disenguages the clutch. In order to...
Thats great, now you have the measurements. You should probably try to pull them out to get them though, or find someone that has them out to get more exact measurements. Also, you should try to get a mm measurement as well as a standard, just in case. But if you think your measurments are...
All you would have to do is measure the mount diameters of the original mounts and order some inserts from prothane that fit the specs. Press the original mounts out and put the new prothanes in, that easy! When one of you gets the measurements be sure to post the specs so we can search for the...
I did search, Im no noob. I could not find the specific information that i needed, all i could find were posts saying how to do it but none that stated the effects of doing it. But thanx to this thread I ran the PCV valve stock again.I would have done the fuel filter but there is absolutely...
Today I capped off the the intake manifold plug that went to the PCV valve and ran the PCV hose to my catch can. What are the effects that this will have? With my understanding i would think that by doing this the motor would not be sucking in bad gas vapors in turn allowing it to burn a more...
i know my front right wheel bearing is going out and im pretty sure on our cars you cant just buy the wheel bearing, you have to buy the whole hub. Please correct me if im wrong or if you have any other suggestions.thanx
98 Eclipse GST 5-speedI have a full prothane motor mount kit but the motor still rocks forward and backword in the engine bay as if the axles have play in them whenever i give it even a little gas. It feels like the motor is twisting forward from the torque untill sufficient speed is built...
Ive narrowed it down to two selections after doing a lot of research on the subject. Im not very educated on trannys so i would like your opinions. I currently have a TRE tansmission with Quaife Diff in my 98 FWD, i use Penzoil Sycromesh in it and my up shifts are clunky and the tranny does...
ill have to log it again to give you the specifics, ill do that within the next couple of days so keep an eye on the post. But im running 19-20lbs, the car pulls like a beast, it almost seems like a sudden stall, and on one log that i looked at a long time ago it looked like my injectors...
The only place it could be leaking is at my throttle body shaft seals or my injectors, i use all Tbolt clamps and Samco IC hoses. Wouldnt my boost fluctuate a lot if i was leaking that much boost though.
I have an evo 16g and i think ive maxed out my injectors. When i log it on my DSM LINK it says my Duty Cycle is 101%, also when i drive at WOT and am at about 6500-7000 rpm the car missfires or the injectors shut down or somthing. Has anyone ever run into this situation, if so what happend?
Im sorry, i posted wrong information about my throttle body in my earlier post. It only has 1 vacum port on it and it has none comming out from the sides. My guess is that it is a JDM model that may have come off of a Galant VR4. Is my assumption correct?
The throttle body on my car is not like the 91-94 TB's but it works great. I have a 2g with a 6bolt motor swap. My throttle body has only 2 vacume ports on the top of it but it is a 60mm throttle body. I do not have any of the vacume lines hooked up because i dont care about emissoins but i...
I wasnt sure if i should make a writeup on this or not so im gonna post it here first and you guys can let me know.If any of you are like me you research a subject before proceeding to do it. I did this with the suspension installation of GC Coilovers on my KYB AGX shocks and still had tons...
What where all the parts that came with your GC coilovers? Mine included a large rubber top mount, a small red cupped bushing, the spring, the perch, and a large steel washer.Does that sound right or am i missing pieces?
Im refering to the washer that you slide on the schock first, its the very first thing that goes on the shock. Like on the front when you slide it down it should stop before it sits on the shocks built in perch and the coil over should sit on it. My washer is too big and slides all the way...
I am putting a set of GC coilovers on KYB AGX and im running into some major problems. I have some questions:1.) I ordered GC top mounts for the front so i had to get the springs 1" longer, is this correct becuase it seems that when i put the shox together the spring is already loaded...
I played both forza and GT4 and all that say Forza has better graphics, you must be smoking crack! GT4 is much more crisp and sharp as compared to forzas Cartoonish graphics, and the mirroring affect in Forza sucks, you can see the frames at which the objects reflect off the cars which is no...
Im leaning towards doing the KYB AGX + Eibach Sportline combo, does anyone know the Eibachs spring rates. Also, what companies make springs with custom spring rates, im trying to do a 400/500 LB combo.
Im buying a set of D2 coilovers but i dont know how im suppose to adjust them to give me the right size drop. I really just wanted to go down maybee 1.5" or 1.75". Is there some way to tell how much of a drop it will give while the coilovers are off the car or do i have to guess first, put...
I posted getting them for 699 and yes, they do include drilled, slotted, and zincwashed for that price.http://www.streetortrack.com/baer-brakes-88-00-mitsubishi-eclipse-front.asp