Selling a brand new in box Walbro-Ti Automotive 450Lph High Pressure e85 compatible fuel pump. Model number is in the photos.
Asking $90 shipped and PayPal'd
Call/Text 952-406-9540 or private message if interested.
Thanks
For sale, ceramic coated Garrett GT35 turbine housing. I never ran it, I'm going v band I think so it's for sale.
I cleaned up some casting flash, smoothed the inlet and outlet a little bit, ceramic coated it, bolted it to my FP HTZ 3586 and it's sat on the shelf ever since.The following is a...
FOR SALE: GM 3" MAF from LS1 with 2.5"-to-3" silicone couplers and ECMlink MAF Cable. Cable has provision for IAT and BAROb sensors.
Would like $60 shipped and fees
Tex nine5two_406_nine540
Just some quick flicks of how I did a single hellcat pump for a friend's 2g. Somewhat down and dirty but it turned out ok. I've seen people use t-taps on these to run them and it blew my mind. I used GM weatherpacks and used a relay with large AWG wire right off the battery. Used the old pump B+...
selling my AMB aero 2G dsm version 2 widebody, had a baby and it would be a long time before I could mount the kit.
I have all correspondence with Andrew brilliant, all original renderings and all invoices. as far as my knowledge goes, only 3 kits were made, I was the first to inquire about...
I discovered at the very end of last season that the front left halfshaft support bearing bracket bolts on my 95 GSX with a 1g swap had loosened. This caused both holes to get stripped out, and one got damaged pretty bad. maybe about 1/3 of the boss itself cracked off. The bearing itself is in...
I wrote this based on a combination of very reliable and experienced sources and put it all in order. Good information here, read the pdf.A monkey could tune if he could read this and had some practice. From initial checks, setting up a MAF table, scaling a MAF, dialing in a VE table from...
selling my solus ultra with 17.2 software with euro cars and motorcycles. includes snap on case and charger. it has always had a screen protector on it. Very useful tool for diagnosis, which a lot of our DSM's require. this tool was $3800 new. I upgraded to a modis ultra, so I no longer need it...
1995 gsx
fp2 cams
6-bolt magnus bottom end (compression test yesterday: All cylinders = 95psi first crank, 168-175psi after 5 cranks. throttle 100% open.)
fp3052 turbo (garret gt3076 with different hotside)
external wg with dump pipe
coil on plug conversion (no ignition box)
front mount
id1700's...
Any parts out there?
Custom interior panels
Transmissions
Aem stand-alones
T4 Hot sides for GT35
Hks exhaust
Driveshaft shop axles or driveshaft
Race seats
ARP 6-bolt head studs, new in box wrapped $90 shippedGM 3" MAF with couplers (2.5" to 3") $45 shippedECMlink MAF cable $40 shippedSBR ported 8cm² exhaust manifold with bolts to head and turbo and spacer $65 shipped (runner #1 tapped for egt probe and includes spacer. Don't think the spacer...
I have a 1g in a 2g swap and am installing the fp dsm manifold. I have an FP30 turbo but there is a sizeable gap between the turbo and the header. There was a spacer between the manifold flange and head on the Mani I removed, but if this is supposed to be "bolt on" why would I need the spacer...
I just ordered a FP cast-iron exhaust manifold and have a few questions...1) My current SBR mani has some type of spacer between the flange and the cylinder head. is this typical and do you think I will need this for my new FP mani? I'm using an FP30 turbochager.2) the new header is ceramic...
I recently replaced my belt for the P/S pump, alternator, water pump because it split and slipped off. I can't seem to get enough tension on the new belt. It is very noisy on start up (worse than the normal for these cars) and I think it's slipping at WOT. I'm not even sure I have the right bolt...
Thread title speaks for itself. I recently developed an exhaust leak at the flange of my Buschur Racing 3" downpipe. Buschur said they don't use a gasket on those (even though it looks like I have one squishing out where the leak is) so they only resurface them. I figured it may be more cost...
I just switched to e85 and had a tune done. the car pulls good and cruises very good 99% of the time. there are some issues that have started recently though including...
when I go WOT I have a stumble/miss at 6500 basically on the dot everytime. the whole fuel system was just redone and I...
my 2g dsm isn't running right. My wideband shows around 16:1 at idle and ecmlink is reporting between 11.4 to 12 afrs at idle. Stft are 12-16 percent positive. At cruise I'm lean on the wideband as well. the car sounds like the timing is off at cruise and idle too. kinda the Subaru burble. if I...
WORKIN ON MY 95 GSX, 74K ON BODY, MOTOR AND TRANS INSTALLED AT 69,228, TURBO AND ALL OTHER MODS INSTALLED AT 70,728. E85 NEXT MONTH AT DB PERFORMANCE. HAVE WALBRO 450lph AND ID1700'S ON MY TOOLBOX RIGHT NOW. ALSO GOING SPEED DENSITY AT THE SAME TIME. WHAT DO YOU THINK OF THE BUILD?Engine: 1991...