I noticed this noise when putting a 2600 act clutch in. On Jacks websites they said using a heavier pressure plate can cause "womp womp" noise. Is this what I am experiencing? The noise is onset usually by load ie: a downshift.
Well it's getting warm again in souther california. Already hit 80 degree weather the other day, I have been dealing with cooling issues since last summer. I think I have pinpointed it to my ac condenser, I believe that it's impeding my airflow. But that is because almost all my fins are busted...
Alright I just bought this kit from STM they told me it was a straight drop in, I was replacing my old 190 wally. But these connectors don't look like it works unless I am missing something. Tried the search but couldn't find much information on them.
Hey all,
just got my tial in my car and thought I picked the correct spring. But I am still having issues with flutter/surging. At part throttle if lift off my foot, it takes a sec or two to open, cruising is where it surges on low boost, but wot open great.My vac is between 17-19, but I...
Hey all,
I have had this dsm for about a year now and even on the t25 had some cooling issues during the hot vegas summer. Now I am on the a 16g with a heat blanket on my manifold and coated o2 housing. Running a mixture of 70% distilled water and 30% antifreeze, I still get hot temperatures in...
1). Any boost, vac, or exhaust leaks?
Boost leak tested 5psi above your max boost with no leaks?
Yes
2). Verified mechanical timing?
Yes
3). Verified base timing?
Yes4). Ignition system
COP or Stock Coil: Stock
Wire brand and Age: NGK looks fairly new, already had them on the car but the owner...
Just changed my coolant today, I cannot really tell what this film on top looks like. To me it looks like gasoline, if you've ever seen gasoline float on water. Previously I was running distilled water and antifreeze with water wetter just got knowledge purposes.Please don't be a head gasket...
After some hot weather in California I am looking to make my cooking more efficient.Mods; e3 16g, fp mani with blanket, o2 housing coated,ets street fmic, and other supporting modsCurrent setup; original radiator(have tried to flush it out) only running Ac fan always on with ecmlink...
Well I changed my plugs about 2 or 3 weeks ago, and today I did a compression test(numbers turned out great). But for some reason my idle is not steady, the only thing I can think of is I put the wires on wrong. The car is a 96 eagle talon and I've tried the two firing methods posted on ecmlinks...
TLDR I screwed up my exhaust what's the cheapest way out.Hey all, want to give you some
back story first. Installed hks catback to cat and stock downpipe. Then instead of buying a downpipe, I had an exhaust shop make one(not sure if it's press or mandrel...and the used the stock dp flange) and...
Hey all,
I need some help with my exhaust. I have a HKS catback (cat removed) welded to my downpipe that an exhaust shop made for me. How they did this was, cutting the stock downpipe after the flange and bend from the o2 housing side. Then welding up a bigger 3 inch I believe pipe to the...
Hey all, I have had an exhaust leak that didn't seem to bad. I thought maybe this car just needed a new gasket, well now I am installing a e3 16g and also fp exhaust manifold. During the removal process I came across this bolt of the exhaust manifold (bottom right) that looks like someone cut...
Hey I just rebuilt a 14b with 7cm hotside. I seem to lost the bolts that attach to the wg and housing. Anyone know the size or where I can get them? I also need the clip for the wg to the hotside.
Well I bought HKS Hi power because it was on sale. Regretting it now, I want to run a cat delete and can't seem a downpipe to fit the 2.5 inlet. I wanted to take it to an exhaust shop but they said it would be to hard to cut that 2.5 portion out and weld a full 3 inch. Any suggestions I'm all...
Hey guys, after selling my gst which had a megan downpipe cat delete to srs (ebay exhaust). I now am looking for something new on an awd talon. I was looking at thermal mated to PR dp. OR buying a megan muffler and getting a custom cat back made with a PR dp (). Wanted to hear some feedback on...
Fixed some leaks, but every time I pressurize the system to 12-14 my tester falls off. The turbo is a s16g, and I am thinking its the adapter on the turbo inlet(black rubber thing). Has anyone else had this problem? If so did removing the black adapter and getting a smaller coupler work?Any...
Hey guys, I plan on running e85. I have stock fuel lines, will they slip right over this? Also I did some reading on the setup, can somebody clarify on how it work. I know it read ethanol content but then does it just change the tune real time?If I missed something in the threads posted can...
Hey guys I got a catback exhaust and down pipe all 3 inch. But to me the car dosen't seem loud enough, I never really got a good look at the exhaust until I looked tonight. Is that a resonator after the rear o2, and if I cut that out and welded a straight 3inch inplace. Would I gain sound and...
1). Any boost, vac, or exhaust leaks?
No2). Verified mechanical timing?
Yes3). Verified base timing?
Yes4). Ignition system
COP or Stock Coil: Stock
Wire brand and Age: NGK 3 months
Spark Plug brand, type and Gap: NGK-BPR6ES/.0275). Motor health (Compression Test)
Cylinder 1: 123...
Hey guys I just installed an SRS (ebay exhaust) it is full 3 inch except were the cat inlet it. I also have a 3 inch megan downpipe which also restricts to 2.5 for the cat. I am running no cat and the exhaust bolts up flawlessly. How beneficial would it be to cut out the 2.5 area and weld them...
Hey guys, car is running good. No idle surge except when I turn on my AC. My idle actually goes up 150 and my ISC position in link goes up to 70 from 30. I tested my alternator for volts and is good, should I go ahead and test my iac?Any input would be nice.
Put a small 16g in around 400 miles ago today I noticed some smoke. Looked at my engine bay and saw this oil leak. I bought the feed line off extremepsi and it said for a 16g. A buddy of mine said the fitting looked a little funny. Think I need a whole new feed line?
Mods: s16g, dp and exhaust. Running 12ish psi. My main concern it the knock I am getting at the last pull I had 4.6 degrees. Any input would be great thanks.1). Any boost, vac, or exhaust leaks?
Boost leak tested 5psi above your max boost with no leaks?
N/A
2). Verified mechanical timing...
Well I think I am in the correct area to post this. Anways some background car is a 2g eclipse, srs(ebay exhaust), with megan racing downpipe, s16g. My question is I am going crazy to figure out if my exhaust is a full 3 inch now, I unfortunately didn't install the exhaust system because I was...
Had some work done to my car, exhaust, turbo, and a tune. Happy with the work but I feel like the car wasn't tuned. When I open up link I see now adjustments to fuel trims, and MAF comp. Just wondering if theres a way to tell if I got a tune.
Hey guys doing some maintenance and installing my Hallman Pro MBC. I am T'ing off my BoV and I know its not the best place but my jpipe has no fitting yet. Anyways I am running a hose from my Internal WG to the boost controller, but my fitting seems loose on the waste gate I can just pull the...
I have a small 16g and need to put on my hallman mbc, my Jpipe has no nipple. So can I just drill a hole and tap it for a fitting? and should I take it off to do so because of the metal shavings?Thanks
Recently bought a used dejon intake, I just automatically thought that it would be easy switch out from the stock rubber snorkle. Mine looks like this but maybe a tad shorter, but the BOV dump tube is in the way back by the turbo inlet. So my question is do I need to get a FMIC to make this...
My 97 gst has, idled weird for awhile now. Just got the car about a month ago replaced plugs, put a vibrant air filter in and thats about it for the mods. Been doing maintenance work for the most part the car is showing two CEL codes P1105 (barometric sensor) did some reading on that but it...
I am in the process of maintence, just bought the car it was one owner and in great condition. I am not sure if there has been any work done on it, but I just did the timing belt. Anyways I am having a problem when I give WoT in 2nd, 3rd, or 4th it has trouble getting up in speed. It's almost...
I bought my 97 gst from South Carolina (I am in Monroe, LA) and my dad drove it from SC to Louisiana for me. He put around 1k miles on it (Car has 120k). This car has only been owned by one person and only been in SC, going crazy to find if the timing belt has been change already. Is there any...
So my check engine light is on and its an o2 sensor, and I also have p1105 (barometer something). Not sure what is wrong but it does idle different on start up. I also have no breather hose coming out of the valve cover, I just picked up this car and never had a hose. My questions are could this...
Just picked up my stock 97 eclipse gst for 3900 :D. Anyways I noticed a nipple on the left side of the valve cover, did some reading that this was the valve breather hose. But there is no hose, has anybody ever seen this? Is it possible that it just get disconnected and it somewhere there? Whats...
Would this http://www.ebay.com/itm/1990-1999-Eclipse-Talon-Laser-1G-DSM-4G63-OEM-BOV-Blow-Off-Valve-TURBO-/331251391365?pt=Motors_Car_Truck_Parts_Accessories&hash=item4d201f1b85
replace my whole 2g bov set up? Basically wondering if it was like a bolt on considering it comes with the ic pipe.
Hey I am about to pick up a dsm first time owning and I am pretty excited. I want to put a wishlist together to get it all organized. I did some reading on "Basic Horsepower Upgrades" a thread started on this fourm, and I want to get a Tial 50mm QR BOV...
Hey, whats up my name is Anthony. Hopefully in the next few days I will be purchasing a 98 gst with 150k miles on it. From what we know so far it is "stock", has a boost gauge, and boost controller(ebay) and a "hks bov". He says he is running stock boost, but when my Pops drove it he read 16. We...