Ok so my profile needs updated badly. The vehicle first:
97 Talon TSi fwd
6-bolt swapped built.
FIC 1650s low impedance
JMF street intake
GT35R
T3
AEM wideband
AEM boost
DSMLink v3 full speed densityI'm trying to get the car started and it wont fire.
Timing is verified, compression checks...
Here is my question, plain and simple
I have my stroker pistons from my 7bolt 2.3 and i want to mate them to a set of 156 rods with a 88mm crank in a 63, my question is will it work?
Im not worried about compression because im forcing the air with a gt35r so i want a long rod motor to rev...
Ok so i have a 2g
Rebuilt another engine with all new bearings and a built head w/ crower 272s
And come to avail i start the car after priming the oil pump and im getting a knock from the bottom end, and when i rev it up it sounds like the police at the front door.
End play is within spec, rods...
Ok so i have a 99 spyder with a 2.3 stroker, arp studs, mls hg,
Now here is my issue
Got my stroker running again and i keep loosing compression on #2 from 160psi to 0psi going from cold to warm, just built the head with ss undercut valves and new mls hg, what i dont get it i get compression...
I have read every thread possible to try and figure this crap out and im left to post my issue99 gst
2.3 stroker
Built head
Hks 272s
Fic 650's
Mhi e3 16g
FmicOk so i had an issue after i built and installed my 2.3
Did a nasty burnout and ended up with flywheel bolts backed out of the...
Built a 2.3 and blew up my trans bearings and syncro's im already getting a decent fwd tranny but would like to have a second tranny on the side since stock fwd trannys are prone to giving out with 2.3 strokers so if you got one let me know
Ok drivers i have built my 2.3 and am needing a clutch stage 3 + and either way will be finished with dropping my motor and trans back into my car and am going to get tuned
Now heres what i am after...
I would like to interrupt this marriage to announce racing season is open
Screven dragway is...
Heres a list of most of the parts i have for sale in savannahBrand new nippon pistons w/ new rings on g4c rods, also have a second set of nippon pistons w/ rings on g4c rods that i pulled when my stock crank spun the mains, also have a second set of unopened nippon rings, .5 oversized king...
Ok so ive owned my spyder for a little while and its not my first dsm but this is my first 2.3 stroker build so here i go
Mitsubishi 100mm 4g64 7bolt crank
Wiesco 85mm 8.5:1 stroker pistons
K1 sportsman rods
Oem bsek
MHI TD05H big 16g
Prothane motor mount incerts
Fic 650's
Hks 272's
Fmic with...
Ok fellow dsmsavannah drivers, I'm looking for someone who has the tacktrix OpenPort that can help m out with a good tune and flash, I recently installed a true mhi e316g and am getting bigger injectors, I need someone who possesses the tacktrix OpenPort and if you do and can hook me up with a...
Ok so I don't have one of theses since replacing all my boost lines, but, what is the restrictor plug in the boost line that comes from the compressor to the t between the wg and boost selenoid for?
I recently pulled a set of cams out of a 95 gsx and found them to have the I casted into them both I know which one is intake and exhaust due to the notch in the intake camshaft for the cas now my question is what duration and lift are they are. Ive looked in the tech guide but it says...
What's up everyone in the 912 area, I'm looking for a few miscelanious parts, if you got some laying around it would be awasome, looking for either hard pipe setup for a stock side mount or hard pipe for a front mount not looking for free which would be awasome but cheap is nice too, I've also...
Ok so I bought this 93 talon n/a today in jacksonville fl. And while driving the 150 miles back to savannah the car intermittently "choked, bucked and sputtered", I checked the dizzy and its turned all the way advanced, so I checked the plug wires and it looked like they are wired one plus...