Does anyone know what the gear on the end of a speed sensor for a 99 eclipse rs is called? thanks

so leave the plastic gear in there and just get another one?

I have 99 eclipse rs. My speedometer quit working so i checked the speed sensor out and it wasn't putting the proper voltage out. I bought a new one and went to replace it, I unplugged it and removed the one screw. I went to pull it out and had to pull hard and a piece came loose from it and...

Two USA Made Hatch Lift Supports Shocks Struts Arm Props Gas Springs 4952LR | eBayYou can get both of them for 38.70. They cost more at advanced auto or auto zone. I just replaced mine.

No the axle came out easy. Had a hard time getting the old hub out. I used a hammer and chizel to get it out.

the wheel bearing on the front passengerside was bad. So i bought a new wheel hub with bearing installed replaces good as new now.

I checked to make sure rim is tight. When I drive there is a terrible rubbing noise coming from the front passengerside of the car. There is a slight play in the wheel but I think its the tie rod end. But the noise sounds terrible I took a video while I was driving down the road about 45 mph I'm...

ok thanks , Ill check this out more in the morning, its dark now. thanks for the help. ill post when i get it resolved.

When the wheel is on and im driving I get a rubbing noise. So I took the tire off and put the car in netural so could turn the rotor and thats where im hearing the noise from the caliper rubbing on the rotor. I wasnt sure if there was supposed to be side to side motion.

Here is a video showing what is going on.2013 01 26 16 57 31 6331 - YouTube

Yeah the bolt has the piece of rubber on it. I havent bleed the system. I was just driving down the road heard this noise. I unbolted the caliper left the brake line hooked to it. so why should i bleed the system. my brake pads have alot of wear left. checked rotors out it doesnt looked warped...

Im sorry i typed the wrong thing. the caliper bracket is tight to the hub and doesnt move. when you tighten the bolts on the caliper to the bracket the caliper has side to side movement

yeah the bolts are about 3 inches long. They tighten up to the caliper but have movement in the caliper mounting bracket side to side

On my passenger side brake caliper the bottom screw is tighting up with no play or movement but the top screw on the brake caliper is tightens up but has some play from side to side. It is making an awful rubbing noise. Can I just change the hardware or do I need a new caliper?

I think rim 2 looks better

I have 17 inch gsx wheels and two of them are bent. They are bent on the outside lip. Will this have any effect on the wear of my tires or the way the car rides. I stopped at a local wheel repair shop and the guy said he could fix them for $115 each. Ill add pics soon. Any help would be great...

Can you post a video or and audio recording of the exhaust. I read that its a $5000 fine to get caught without a Catalytic converter.

I decided to go with the Goodyear Eagle F1 Asymmetric tires. Ill do a review on them.

Ok thanks to everyone and there inputs very helpful!

Im not being lazy. your being a dick! ive looked at tire rack.com all the tires have bad reviews. i was just wanting to know what tires people would recommed and have had a good expericence with. Sorry for asking!

I'm looking to buy some new tires, size 215/45/17. Its a daily driver need an all season tire any suggestions. thanks

ok, thanks alot. ill check that.

Whenever I have my heat on defrost it blows air out of all the vents in the car. No matter which position I put the vent control in, it blows out of all vents all the time. Any ideas what the problem is?

Great story! Can't wait to see the next season of your car build. Good luck car is amazing!

Im thinking of rebuilding the top half of the motor, since im burning oil. i just wasnt sure if the whole motor needed to be rebuilt or if you could just do the top. i love my car and i want it to run as long as i can keep it going.

welcome to the forum. cant wait to see your build wwhen your done. good luck

Thanks i'll check into it.

Ok thanks for the info.

ok first off my car has 188k on the odometer. I have white smoke at times coming from the exhaust. I'm burning oil. It seems my valves are burnt. Is there any long term damage if valves are not replaced? My question is it worth just rebuilding the top half of the motor? or should the whole motor...

i found it after some seaching.DOOR / INTERIOR TRIM / Storage box

this is on the passenger side door. it is broken and need to get a new one. but i dont know the proper name of the part

thanks. i have a new clutch. im going to install it soon and was just needing to know what to expect. thanks

is there a thread on changing a clutch? thanks

is there a thread or post on step by step instructions on changing a modular clutch? i have a new clutch that i m going to install in the spring and want to know what to expect. thanks

yeah i had a timing belt break. bent valves for sure.

thats what im going to first in the morning is change the master cylinder and hope for the best. if it doesnt work ill be putting in a new clutch.i guess i was lucky. i changed the master cylinder and everything is good now. thanks for everyones help.

ok thanks. i thought so but wasnt sure.

do you need the line up tool when changing a modular clutch?

Thanks alot for the information. Im going to change it tomorrow. Should I change the master cylinder first and bleed the the clutch before i change the clutch. It may have ruined it running with no fluid. Thanks guys for the info glad to be apart of the dsm family

welcome to the forum. good luck with your car

ok i found the leak, it is running down hw clutch pedal. where is it coming from?i need help please? thanks

last saturday my clutch pedal was soft. i checked the fluid it was empty. i added some and bled the line. petal started feeling better. so i started down the road. a few shifts later i stoped at a rred light and couldnt go to first gear.i finally got it in gear and got home. i had a friend look...

welcome to the forum, good luck with your car

ok thanks

ill have some up tomorrow. my clutch is out. my car is at a friends housedo you know which is better, ceramic disc or kevlar disc. im trying to figure out what type of clutch to get

which is better ceramic disc or kevlar disc in a clutch kit?

i have a 99 rs. i have a problem with clutches going out. my car is parked, while i search for a new stronger clutch. i have been reading alot of reviews so im basing my chocie on what i have read.