These will fit both 1G and 2G Mitsubishi Eclipse, Eagle Talon or Plymouth Laser. These brackets will work with EVO 8, EVO 9 and EVO X brakes. You can "clock them up or down" with these brackets! If you use the EVO X Brembos you have to use the EVO X rotors. The brackets will come with the...
Hello these brackets will save you a few hundred $$ and its a great choice to mount your brembos attached are the brackets that bolt-on with zero grinding or modifications done
Hello,
I have a fully built 1998 GSX i need help with im located in queens NY 11101.
fully built 6bolt motor turbo and fully built 2g transmission with a 3400 stall convertor DSM link V3
force four Shift Box SMART 100.1(not installed)
ISSUES
Idle is surging car stalls car overheats & it's stuck...
ORIGINALLY OUT OF A 1990 EAGLE TALON TSI 4G63 2.0L TURBO BARE 6 BOLT ENGINE BLOCK
HOT TANKED CLEANED MAGNFLUX TESTED
HONE BLOCK 0.20/.50
TORQUE MAIN & CHECKED LINE BORE
BY S&A ENGINE BUILDER IN LONG ISLAND CITY 3-26-19
asking $500 OBOFOR FASTER RESPONSE CALL/TEXT 917-407-4065...
(1) FP INTAKE NON RECIRCULATING WITH COUPLING & FILTER (DIRTY) $70
(1) USED UPPER INTER-COOLER PIPE WITH GREEDY BOV $80
(1) NEW 2.5" UPPER INTER-COOLER PIPE WITH TIAL FLANGE $50
Welcome to DSM tuners post a pic of your ride. make sure all your maintenance vacuum leak & boost leak checks are all done. 99.9% of most issues and problem have been answered and/or discussed here. Rear axles are a pita to find I had mine rebuild. GOODLUCK
Hard to tell if the valve cover is cracked from a picture it would have to be removed cleaned up and inspected. I would recommmend a change and upgrade to an EVO oil cap looks better and comes with a new seal to rule that out.
Did you change the half moon seal on the valve cover?
If you have an machine shop or engine builder I’m sure he would charge to look and inspect them for you.
Hold on to the old ones hey you never know.
GOODLUCK
I would send the ECU in for testing its free.
Also set the mechanical timing correctly at the cam gears and crank pulley
if the CAS is still loose tighten it at the mid way point.
GOODLUCK
A good combination of internal engine parts can help meet your goals Manley makes great internals. You should look into a high compression ratio and a E85 piston OEM crank is fine. I’m not a fan of EAGLE products
Look at Manley CP rods or better a better clutch a bigger turbo 6266 or equal a...
A quick way to tell if your getting fuel loosen up the line from the fuel filter to the fuel rail crank the car if fuel leaks out your getting fuel. i would check all the fuses and spark next.
GOODLUCK
Oil feed line for 1G DSM is connect to the oil filter housing for the best possible oil pressure.
I personal dont use coolant to cool the turbo only oil.
I also had the same issue like most ppl already mention portable map gas with self igniting torch (cheap) $40 @ home depo & lots of lube.
In the process of removing them i destroyed mine and had them rebuilt by ARC manufactures they did an amazing job 24hr later they were new again .GOOD LUCK
I used safter i replaced the fuel neck i coated it with rustoleum and under coat.
i used some of the old mounting and hardware and had to buy new fuel hoses to make it work.
I was replacing sub frame bushing & rear suspension shocks springs sway bar link & 3G suspension
it was much easier to...
I had the same problem GSX & GST fuel necks are different. Its almost impossible to find a GSX fuel neck .
I used a fuel neck out of a 97 non turbo spyder found at a junkyard for like $10 minor modifications and all new extended fuel hoses but it worked.
i would try miller import partsGood luck
All parts off a 1998 mitsubishi eclipse gsx auto2 new rear sway bar links 4056a014 $15.00
2 used rear trailing arms lh & rh mb914381 $25
2 used rear lower control arms lh & rh mr131754 $45
2 new rh lh ball joint lower control arm gst rs gs only mr162573 $20.00
used 18mm rear lower sway bar...
I would like to get a full spec Turbine Compressor part number is it a Dual Ball Bearing Turbo? what flange what style compressor housing what the rated hp?there is no name plate here a few numbers H2613 and 9722-30
1. 1g or 2g 6 bolt water pipe off a 1g but modified to be a 1g n/t water pipe bottom coolant line to turbo is blocked off cleaned up sprayed flat black $50
2. 1g or 2g 6 bolt thermostat housing both top and buttom cleaned up and clear coated to prevent rust $40
3. 1g or 2g O2 housing with dump...
Whats up dsm tuners not new to the site but picked up my second dsm
first one was a gst spyder with i had to sell a few years back but now i
picked up another in Virginia for $2,200 bone stock 2g gsx 146xxx miles cayenne red pearl tan interior hit in the front.
i already made repairs to...