The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support ExtremePSI

461/1000 - Long term build

This site may earn a commission from merchant
affiliate links, including eBay, Amazon, and others.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

slugsgomoo

20+ Year Contributor
472
59
Nov 10, 2002
Seattle, Washington
slugsgomoo submitted a new DSM Profile :

461/1000 - Long term build

my1D2gX.jpg


Read more about this vehicle here...
 
Last edited:
I actually have some plans to autocross but that was actually at a drag racing event called "NW Street Car Challenge". It had dig & roll racing to 1320 & 1600' and was pretty fun.

My car is preposterously laggy for autocross though.
 
I'd like to, but I doubt I'll be coming to the race in spokane, it's simply too far to risk going without a way to bring the car back if I break it. I'm looking forward to some west side events though, or possibly even Renegade in Yakima.
 
Nice, man. I'm assuming you're getting the tune worked out? How's the motor doing?
 
motor is really tight, runs well. I'm not really tuning much more out of it at this point, since my injectors are 1000cc & at 48psi base, I'm running 100.8% duty cycle and that's not quite at redline (car is now healthy to 9500, log was breaking up at 8100). Still healthy AFRs and the car seems happy so :idontknow:

461-25psi pull.png


Also worth mentioning that this past fall I installed some brakes that are capable of dealing with what the T67 can bring...

reAzCkZ.jpg


So I took it out for a spin this weekend, but mostly it's just been in winter mode.

fK7VEjb.jpg
 
Your build is one of the few I could drive over my own, Andrew. Absolutely clean, and every detail is done right.

Any plans to make the shootout this year?
 
Last edited:
So after 5 years, and not that many miles of 2.0L goodness, I pulled the motor and sold it to a local to go into a 2G auto car, hopefully he's able to make some good times with it. The car was definitely fast, but I have had a 2.4 sitting around partially assembled for the last three years and I needed motivation.

New setup will be a 10.5:1 2.4L with a 2g head, some other happy hooey to go along with that. I'll still have the HKS manifold with the T67 because old school is... well cheap because I already own it. :D

Also converting to a manual master brake setup, using twin Tilton MC's and a Wilwood balance bar. Hoping that turns out the way I want it to, but I'll probably hold onto the stock lines, prop & master until I decide I love it, before I sell them, just in case. :D
 
23 - JwtPmuQ.jpg
So I haven't done a ton in the last two years, partly because when I made the last post I had a kid who was under 2 months old, and life got busy. In the meantime I did a gut to the studs/rafters/joists remodel of my main bathroom... Y'all know how it goes.

In any case, the brake upgrade is done, and I'm adding a pic to this post, but the whole set of pics is on imgur and I don't feel like reposting, so click here

Finally, this setup is probably not easily duplicated, and realistically, the benefits versus something like an Ostar setup may not be huge- and that's cheaper and less complicated (and basically bolt in), so YMMV.

There's some interesting tech stuff I've learned throughout this though:

I will say, for anyone staying on power assist brakes, or going to the Ostar setup Craig has (liv4psi/mygsx2120), an adjustable bias valve (especially with a remote to adjust from the cabin) would be a big upgrade over the stock proportioning valve. Wilwood proportioning valve with remote bias adjust (definitely cheaper on summitracing though!). You'll also need one of these bad boys to handle the rear lines since there are only 3 output ports (2 front, 1 rear)

From talking to a few folks with adjustable bias on their racecars, generally you adjust bias towards the rear until you start getting rear lockup under hard braking, and then you adjust back towards the front a bit. It should result in getting the absolute maximum braking performance you can, since you're not under utilizing the rear. TBH, other than having to build lines (either SS or hard lines) to make it work, that's not really any more expensive than an OEM ABS delete, and you get a big performance perk IMO.
 
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned

Latest posts

Build Thread Updates

Vendor Updates

Latest Classifieds

Back
Top