The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support Morrison Fabrications
Please Support STM Tuned

Recent content by Murdertalon

  1. Murdertalon

    1G About 2g Black Box ECU in 1G? Car dies after 3 seconds

    should use the firing order from year it is, Cas inversion setting may be applicable?you should wire an obd2 port into the jumper harness, I believe it only needs 3 wires to function properly (maybe 4)
  2. Murdertalon

    Bastard 1G

    driveline lobro shot. bushings also shot. swapped driveline.rear right caliper sized.modeled maf, re idle adjusted.
  3. Murdertalon

    1G Average 3 bolt rear diff temps?

    Has anyone monitored rear diff temps on our cars?I was just curious what temp range I could expect it to get into. I know oil breakdown happens faster higher temps.For reference I'm wondering about a 1g LSD 3 bolt rear, but I imagine there's probably not a huge difference for average temps.
  4. Murdertalon

    Anyone tired of people trying to devalue our cars?

    TBH it cost me $500 to get my turbo rebuilt. We put a factory new garrett on a 2g couple years ago and just the turbo was 1200.
  5. Murdertalon

    What did you do to your DSM today?

    1g we staple welded the broken sun visor plastic so I could re-mount the sun visor. The other day my buddy and I swapped out the driveline on the 1g. I greased the carrier bearings and used grease to soften the rubber on the bushings. The lobro joint is shot on my old driveline and I have been...
  6. Murdertalon

    Anyone tired of people trying to devalue our cars?

    weird thing to care about. I prefer if my car is worth a big mac and it beats the brakes off of a v8.
  7. Murdertalon

    1G 2G Black Box ECU in 1G wiring

    Wish me luck boys, I just built an adapter harness. I am going 97 to 91. I think I have it ready to test and I also need to grab an odb2 port and solder that in.
  8. Murdertalon

    Galant-GSX/SwapVr4

    This is my buddy B's car. I will ask if I can use his name later. Troubleshooting.Galant GSX Swapped to VR4 Engnie: 6bolt from 1G tsi Wiring harness not the GSX unknown what car its actually out of possibly VR4Link wouldnt connect. Pinout on OBD1 port did not have good ground to pin 12...
  9. Galant-GSX/SwapVr4

    Galant-GSX/SwapVr4

  10. Murdertalon

    Galant-GSX/SwapVr4

    This is the Build Thread for Galant-GSX/SwapVr4. Reply below.
  11. Murdertalon

    What did you do to your DSM today?

    Hey 2G guys.. this LED set works alright. I installed the low beams and now I can see!fahern led hb3/hb4 I didnt have the link handy the other day, just found it in my old order cart. 60$
  12. Murdertalon

    What did you do to your DSM today?

    Installed the drop in LED bulbs with ballast for the low beams.. I can see, so thats nice. Fahern is the brand, No issues so far been running them for couple days.
  13. Murdertalon

    2Ga Talon

    Install LED low beams, nice improvement. Need to install usb charge ports and route for tablet and phone. Need to find a tensioner bolt for the ac and replace alternator belt
  14. Murdertalon

    Bastard 1G

    While driving the driveline started vibrating, the bushings are shot. Possibly the carrier berings shot too, bushings for sure.
  15. Murdertalon

    2G Extremely loud knock, Rough idle and misfire

    those cuts in the pistons are normal, but the lack of soot around them is looking like could have contacted, they are butterfly cut factory.have someone double check timing the dowels should line up at 12 every couple rotations and the other timing marks should drop on, won't be every...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top