TopSpeed - Daily Driver Eagle Talon TSi Build

[TRAYTSi]

Hey guys, I'm not new to the boards. But I am new to owning a DSM.

Bought this 1990 Eagle Talon TSi about a month or so ago. Customer blew up his car about 1 1/2 years ago and has been sitting on the side of TopSpeed Since. I twisted his arm to give it to me at a good price. And the build started!

I'd like to thank Shawn here at TopSpeed Inc. for doing everything to this car. A lot of hard work, and effort has been put into this vehicle these last couple weeks and the results were great. And I thank Doug for the 313whp, and 306tq on our Dynojet at TopSpeed Inc. at 17PSI.

Here are the mods, and upgrades performed.

Engine:
- (NEW) Topline Pistons & Rings
- (NEW) Clevite Bearings
- (NEW) Rods
- Polished Crank
- (NEW) Topline Valvetrain
- AAM Cleaning of Head & Shortblock
- AAM Surfacing the Head
- AAM Balance & Blueprint Rotating Assembly
- AAM Valvejob
- (NEW) gasket kit
- (NEW) Brian Crower 272 Camshafts
- (NEW)ARP Headstuds
- All (NEW) Belts
- Evo 8 Injectors
- Greddy Bov Recirc.
- (NEW) NGK BPR8ES Plugs
- Big 16g Turbocharger
- Walbro Fuel Pump 255lph
- Ported Exhaust Manifold
- (New) Vac Lines etc...
- HKS Racing Suction Intake



Transmission / Transfercase
- (NEW) Fluids all around
- ACT 6 Puck Clutch Kit
- ACT Flywheel

Interior:
- Boost Gauge
- Autometer Oil Pressure Gauge
- Greddy Profec B Electronic Boost Controller
- Apexi SAFC II

Here are pictures of the build

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

All post up dynochart shortly...

 

[TRAYTSi]

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

 

[toofast82]

313whp sounds pretty good for a b16g on 17psi! Do you plan on dynoing it at like 23psi or so? Nice Build! Should make a great daily driver with great usable power!

 

[TRAYTSi]

313whp sounds pretty good for a b16g on 17psi! Do u plan on dynoing it at like 23psi or so? Nice Build! Should make a great daily driver with great usable power!

We broke it in on the dyno. We didn't want to push it that much further. In about a thousand miles or so I'm going to hook up an SMC Meth Kit and try to turn it up a little more.

We will see.

 

[toofast82]

Should run 12s all day on about 21-22 psi if you drive good! very cost effective build though! i would recommend a custom burnt chip though and add some nice features like stutterbox, fuel cut elim, custom a/f and timing, etc. I can burn the chips, if you're interested pm me.

 

[TRAYTSi]

I'll keep that in mind. I'm just farting around with it really. Not looking to spend much. Just use what I got around the shop for fun.