daplatano91
10+ Year Contributor
- 1,170
- 26
- Apr 7, 2009
-
brooklyn,
New_York
I'm currently looking for some help to try to setup my AEM to run sequential ignition. I found it rather odd that I wasn't able to find anything online after a few days of searching. I remember seeing a thread awhile back that Turboglen made about converting your car to fully sequential injection, but that was more info for Motec guys and not about ignition.
I already have the coils run to 4 separate coil output channels and have activated coils 3-4 in the software. The issue I'm running into now is knowing what to set the ignition phasing as. I'm running the Kiggly 12 tooth crank trigger 8 injectors and currently have the phasing options as following:
IGNITION PHASING OPTIONS
Igniton sync - 6.73 teeth
pickup delay comp - 48us
Ign Tooth #01 - 0 teeth
Ign Tooth #02 - 18 teeth
Ign Tooth #03 - 6 teeth
Ign Tooth #04 - 12 teeth
Ign Tooth #05 - 0
Ign Tooth #06 - 0
Ign Tooth #07 - 0
Ign Tooth #08 - 0
Ign Tooth #09 - 0
Ign Tooth #10 - 0
INJECTOR PHASING OPTIONS
Injector phase - 15.05 teeth
Inject Tooth #01 - 0 teeth
Inject Tooth #02 - 18 teeth
Inject Tooth #03 - 6 teeth
Inject Tooth #04 - 12 teeth
Inject Tooth #05 - 0 teeth
Inject Tooth #06 - 18 teeth
Inject Tooth #07 - 6 teeth
Inject Tooth #08 - 12 teeth
Inject Tooth #09 - 0 teeth
Inject Tooth #10 - 0 teeth
Does this seem correct to you. I have this feeling that its wrong because the injector was supposed to be 180* different from the ignition cycle. I can send you a copy of the .cal file if you want to take a look at it.
Thanks for you help.
Frank
I'm thinking I should set the ignition and injector phasing like this.
IGNITION PHASING OPTIONS
Igniton sync - 6.73 teeth
pickup delay comp - 48us
Ign Tooth #01 - 0 teeth
Ign Tooth #02 - 18 teeth
Ign Tooth #03 - 6 teeth
Ign Tooth #04 - 12 teeth
Ign Tooth #05 - 0
Ign Tooth #06 - 0
Ign Tooth #07 - 0
Ign Tooth #08 - 0
Ign Tooth #09 - 0
Ign Tooth #10 - 0
INJECTOR PHASING OPTIONS
Injector phase - 15.05 teeth
Inject Tooth #01 - 12 teeth
Inject Tooth #02 - 6 teeth
Inject Tooth #03 - 18 teeth
Inject Tooth #04 - 0 teeth
Inject Tooth #05 - 12 teeth
Inject Tooth #06 - 6 teeth
Inject Tooth #07 - 18 teeth
Inject Tooth #08 - 0 teeth
Inject Tooth #09 - 0 teeth
Inject Tooth #10 - 0 teeth
I already have the coils run to 4 separate coil output channels and have activated coils 3-4 in the software. The issue I'm running into now is knowing what to set the ignition phasing as. I'm running the Kiggly 12 tooth crank trigger 8 injectors and currently have the phasing options as following:
IGNITION PHASING OPTIONS
Igniton sync - 6.73 teeth
pickup delay comp - 48us
Ign Tooth #01 - 0 teeth
Ign Tooth #02 - 18 teeth
Ign Tooth #03 - 6 teeth
Ign Tooth #04 - 12 teeth
Ign Tooth #05 - 0
Ign Tooth #06 - 0
Ign Tooth #07 - 0
Ign Tooth #08 - 0
Ign Tooth #09 - 0
Ign Tooth #10 - 0
INJECTOR PHASING OPTIONS
Injector phase - 15.05 teeth
Inject Tooth #01 - 0 teeth
Inject Tooth #02 - 18 teeth
Inject Tooth #03 - 6 teeth
Inject Tooth #04 - 12 teeth
Inject Tooth #05 - 0 teeth
Inject Tooth #06 - 18 teeth
Inject Tooth #07 - 6 teeth
Inject Tooth #08 - 12 teeth
Inject Tooth #09 - 0 teeth
Inject Tooth #10 - 0 teeth
Does this seem correct to you. I have this feeling that its wrong because the injector was supposed to be 180* different from the ignition cycle. I can send you a copy of the .cal file if you want to take a look at it.
Thanks for you help.
Frank
I'm thinking I should set the ignition and injector phasing like this.
IGNITION PHASING OPTIONS
Igniton sync - 6.73 teeth
pickup delay comp - 48us
Ign Tooth #01 - 0 teeth
Ign Tooth #02 - 18 teeth
Ign Tooth #03 - 6 teeth
Ign Tooth #04 - 12 teeth
Ign Tooth #05 - 0
Ign Tooth #06 - 0
Ign Tooth #07 - 0
Ign Tooth #08 - 0
Ign Tooth #09 - 0
Ign Tooth #10 - 0
INJECTOR PHASING OPTIONS
Injector phase - 15.05 teeth
Inject Tooth #01 - 12 teeth
Inject Tooth #02 - 6 teeth
Inject Tooth #03 - 18 teeth
Inject Tooth #04 - 0 teeth
Inject Tooth #05 - 12 teeth
Inject Tooth #06 - 6 teeth
Inject Tooth #07 - 18 teeth
Inject Tooth #08 - 0 teeth
Inject Tooth #09 - 0 teeth
Inject Tooth #10 - 0 teeth
Last edited: