Welcome to DSMtuners - the largest Mitsubishi Eclipse, Eagle Talon, 4G63t and 420A DSM performance resource on the web



















Login



Go Back   DSMtuners > DSM Forums > General > Newbie Forum
Welcome to DSMtuners - the largest Mitsubishi Eclipse, Eagle Talon, 4G63t and 420A DSM performance resource
You are browsing the site as a GUEST. Please login (or register) and gain the ability to post on our site and interact with other DSMers. You also get to browse the site with fewer advertisements. It is FREE to join!

Newbie Forum: Beginner/newbie/general DSM modification questions. First mods, how to run 10's when you haven't run 12's yet, any tech question that doesn't fit in another tech forum. Probationary Members must limit their tech posts to this forum and sub-forums.

Reply
 
LinkBack   Thread Tools
Old 04-19-2010, 08:47 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #1 (permalink)
Proven Member
 

natertater's Avatar
Registered: Jun 2008
Tech Posts: 232
Classifieds Rating: 5
Reputation: natertater is an unknown
Send a message via Yahoo to natertater
1G-specific

e85 with evo 8 injectors


hey everyone! i was wanting to run e85 on my car, since its a little over 2.50 a gallon, and i dont drive the car much. right now i have evo 8 injectors, and a 2g maf sitting in the car. would this be ok to run e85 in there with stock boost? they are roughly 28% larger injectors to compensate for stoich. also, if i were to do the e85, should i keep with the stock 1g MAF (since airflow is right for stock inj) or use the 2g (which leans it out more?)

eventually my plans are hx35, speed density, 3" and e85 on some big mamma injectors, maybe a dual stock fuel pump, or dual 190's


Last edited by natertater; 04-20-2010 at 05:05 PM.

mark post as helpful recommend reputation points    Reply With Quote
Old 04-19-2010, 08:50 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #2 (permalink)
Banana Republic
 

gofer's Avatar
Registered: Feb 2006
Tech Posts: 4,643
Photos: 65
Classifieds Rating: 14
Reputation: You can trust this leader of the site
E85 is actually under $2.50 ga. ($2.49 ) out here... If your running your stock 14b its still flowing more than 25 lbs/min (30 lbs/min to be exact) even around stock boost levels, which is still too much for those Evo injectors. I suggest running the IM that is designed for the head thats currently on your car i.e. 6-bolt head, 1g IM / 7-bolt head, 2g IM or Evo III IM.

Good plans but thats a long ways down the road big guy.



____________________________
-Corey Jenson

E-OCHOCINCO Powered FP HTA68 / stock 7-bolt / Shep 4
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-20-2010, 05:06 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #3 (permalink)
Proven Member
 

natertater's Avatar
Registered: Jun 2008
Tech Posts: 232
Classifieds Rating: 5
Reputation: natertater is an unknown
Send a message via Yahoo to natertater
my bad, fixed my mistake in post. i meant maf, not intake. so evo injectors, stock boost, and 2g isnt good idea with e85? i need to get me a wideband soon!!

mark post as helpful recommend reputation points    Reply With Quote
Old 04-20-2010, 05:35 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #4 (permalink)
Banana Republic
 

gofer's Avatar
Registered: Feb 2006
Tech Posts: 4,643
Photos: 65
Classifieds Rating: 14
Reputation: You can trust this leader of the site
Quote:
Originally Posted by natertater View Post
my bad, fixed my mistake in post. i meant maf, not intake. so evo injectors, stock boost, and 2g isnt good idea with e85? i need to get me a wideband soon!!
I have a 2g MAF you can get off me for cheap, I'll hook it up for a Navy guy like myself. Just PM me.

Evo injectors are going to be TOO SMALL to run on your 14b turbo, you won't be able to get enough fuel to the motor even at stock boost. You'll want to run 660's MINIMUM on a 14b/E85 setup, I have a set in my closet as well.

The 1g/2g intake manifold has nothing to do with the E85 rich/lean or whatever the hell you mentioned in your OP. The intake runners on your head are ported to the size of the runners on your intake manifold. You have a 6-bolt motor which has bigger intake runners, if you put a 2g IM on it its going to be a small runner going into the bigger runners on your head... WHY? Thats retarded. If your still set on running a 2g IM on your 6-bolt head guess what, I have one of those in my closet too.

On top of all this your going to need a walbro 255 fuel pump (fp) and an adjustable fuel pressure regulater (afpr) to run E85 if you don't already have them.



____________________________
-Corey Jenson

E-OCHOCINCO Powered FP HTA68 / stock 7-bolt / Shep 4
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-20-2010, 07:42 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #5 (permalink)
Proven Member
 

JayRolla's Avatar
Registered: Feb 2006
Tech Posts: 5,075
Photos: 5
Classifieds Rating: 7
Reputation: JayRolla is extremely helpful and trustworthyJayRolla is extremely helpful and trustworthyJayRolla is extremely helpful and trustworthy
Not a good idea IMO. First off get a wbo2 before thinking about doing any kind of setup like that. If AFR's are good at closed loop and WOT then you will be fine. But be carefull doing such a setup.


____________________________
Jason~ Parting out my DSM!
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-20-2010, 09:17 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #6 (permalink)
Proven Member
 

FastJetta's Avatar
Registered: Sep 2009
Tech Posts: 55
Classifieds Rating: 0
Reputation: FastJetta is more helpful than not
e85 is awesome...

do what it takes to make the swap... like he said.

wally pump, bigger injector and a wideband. maybe something to tune


____________________________
91 Galant VR4 #1900
2.4 AUTO PTE6776 650 WHP

mark post as helpful recommend reputation points    Reply With Quote
Old 04-21-2010, 04:33 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #7 (permalink)
Proven Member
 

natertater's Avatar
Registered: Jun 2008
Tech Posts: 232
Classifieds Rating: 5
Reputation: natertater is an unknown
Send a message via Yahoo to natertater
no, i plan on running my 1g im, i meant my 2g intake PIPE from turbo to 2g maf. i have everyhting else still there. so i would need 50% larger injectors instead of 30% more? yeah when i get more money, im getting an LC-1 and gauge. i want a g5, but that is like 50 dollars more than g1 digi readout. oh well, later

mark post as helpful recommend reputation points    Reply With Quote
Old 04-21-2010, 05:30 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #8 (permalink)
Proven Member
 

bob123131's Avatar
Registered: Dec 2004
Tech Posts: 449
Photos: 8
Classifieds Rating: 1
Reputation: bob123131 is more helpful than not
Send a message via AIM to bob123131
No you don't need 50 percent larger,and 30 percent larger is a conservative estimate for the most part, but still pretty close. Think about it like this with bolts on if you push the 14b you can outflow the 450cc's by a little. So you would need 620cc just to push the 14b like stock let alone any more. Depending on your goals just get some high 800's or somehting a little below a 1000 still allows relatively easy tune ability with the right tuning software and is enough if you go up to an evo3 16g or t28.

Also dual stock pumps wil not have a chance to flow e85 with a h35. Even if you have the 8 blade and not 7 blade you wont have enough. The dual 190's would ###### be sufficient for the 8 blade and pushing the limits of the 7 blade. You have to understand that turbo flows 53-60lb/min and im assuming at the point of a setup like that you will be pushing it.
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-21-2010, 07:38 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #9 (permalink)
Proven Member
 

natertater's Avatar
Registered: Jun 2008
Tech Posts: 232
Classifieds Rating: 5
Reputation: natertater is an unknown
Send a message via Yahoo to natertater
ok, sticking with gas, how much boost could evo 8 injectors allow for? i was guessing around 15 or 16psi. i read on here a guy was running 18psi just fine on 450cc with a 190. i deff plan on rewiring my stuff, a little too late tonight to start it...

also on 3si, i seen that evo 8 560cc flow more or so around 600-625. still too small for the fun i want to have, but to just straight up run 15psi on e85 should be fine right?

Last edited by natertater; 04-21-2010 at 08:52 PM.

mark post as helpful recommend reputation points    Reply With Quote
Old 04-21-2010, 08:52 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #10 (permalink)
Proven Member
 

RedEyeBanDiT's Avatar
Car: 93' Laser AWD
Registered: Dec 2006
Tech Posts: 191
Classifieds Rating: 0
Reputation: RedEyeBanDiT is an unknown
I have a 190 with evo8 injectors, on a big16g running 21 lbs. They are about maxed out.
Visit RedEyeBanDiT's homepage! 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-21-2010, 09:09 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #11 (permalink)
Proven Member
 

natertater's Avatar
Registered: Jun 2008
Tech Posts: 232
Classifieds Rating: 5
Reputation: natertater is an unknown
Send a message via Yahoo to natertater
on gas? damn... so i should sell these...didnt even really use them much, just put them in about week and half ago...but then again, thats a b16g, moves a lot more air than my little 14b

mark post as helpful recommend reputation points    Reply With Quote
Old 04-21-2010, 09:39 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #12 (permalink)
Banana Republic
 

gofer's Avatar
Registered: Feb 2006
Tech Posts: 4,643
Photos: 65
Classifieds Rating: 14
Reputation: You can trust this leader of the site
Quote:
Originally Posted by natertater View Post
on gas? damn... so i should sell these...didnt even really use them much, just put them in about week and half ago...but then again, thats a b16g, moves a lot more air than my little 14b
The b16g does push a lot more air but he's also running 91oct, your talking about using E85 though. Regular gasoline's STOICH AFR is 14.7:1 while E85's STOICH AFR is 9.8:1, so E85 requires 49% more fuel going to the motor. Injectors are flow rated for gasoline running a 14.7:1 AFR, but your running E85 which is a 9.8:1 AFR so you take (14.7 / 9.8 = 1.5). Stock Evo VIII injectors are flow rated at 560cc on gasoline, your running E85 though... so take ( 560 / 1.5 = 373.3) that means your Evo VIII injectors are going to flow like a 373cc injector on E85 which will be at 100% IDC's at just 21.8lbs/min.

I know thats a lot of math but thats how you figure E85 flow rates on injectors since they are rated on gasoline.

(Injector size / 1.5 = E85 flow rate)



____________________________
-Corey Jenson

E-OCHOCINCO Powered FP HTA68 / stock 7-bolt / Shep 4
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-21-2010, 09:53 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #13 (permalink)
Proven Member
 

jrohner's Avatar
Registered: Sep 2004
Tech Posts: 2,547
Photos: 5
Classifieds Rating: 0
Reputation: jrohner is pretty helpful and trustworthy
You'll need something to tune with. If you run stock with the Evo injectors and E85, you'll be lean. If you run the 2G MAS you'll be leaner yet. You need 650's to run E85 with no tuning.
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-22-2010, 06:02 AM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #14 (permalink)
Proven Member
 

natertater's Avatar
Registered: Jun 2008
Tech Posts: 232
Classifieds Rating: 5
Reputation: natertater is an unknown
Send a message via Yahoo to natertater
alright, so i will shoot for gas on evos then for now. sucks trying to hook up 2g maf to 1g intake pipe, but i have a frozen boost coupler that does the job for now. cant wait for sd adn ostrich...just gotta wait for more money, like in october...stupid waiting for srb....

mark post as helpful recommend reputation points    Reply With Quote
Old 04-22-2010, 07:08 AM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #15 (permalink)
Banned Member
 

ramsack's Avatar
Car: Bicycle
Registered: Dec 2007
Tech Posts: 2,196
Photos: 4
Classifieds Rating: 3
Reputation: ramsack is pretty helpful and trustworthyramsack is pretty helpful and trustworthy
Send a message via AIM to ramsack
the 1g 450cc injectors at stock fuel pressure are really 380cc. so if you are going to run the 36.3 psi stock pressure, you will need something like 680s. if you run what injectors are rated for (43.5 psi) then you may get away with 550s and bumping up fuel pressure a bit (2-3 psi). you definitely want a better pump though. i wouldn't run the 2g mas unless you have something like dsmlink that will let you not mess with timing to compensate. you will be throwing more timing advance into the mix. you could try messing around with it but it's not a set amount change in signal over the entire airflow range.
Visit ramsack's homepage!  View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-22-2010, 08:20 AM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #16 (permalink)
Proven Member
 

JayRolla's Avatar
Registered: Feb 2006
Tech Posts: 5,075
Photos: 5
Classifieds Rating: 7
Reputation: JayRolla is extremely helpful and trustworthyJayRolla is extremely helpful and trustworthyJayRolla is extremely helpful and trustworthy
1g injectors are rated at 450 even at 38psi fuel pressure.


____________________________
Jason~ Parting out my DSM!
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-22-2010, 07:24 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #17 (permalink)
Proven Member
 

natertater's Avatar
Registered: Jun 2008
Tech Posts: 232
Classifieds Rating: 5
Reputation: natertater is an unknown
Send a message via Yahoo to natertater
and when boost raises, fuel pressure goes up 1:1 as well. but yes, i understand all these things. right now its 560cc injectors with a 2g maf hooked up (but not fully plumbed) and i dont drive this car, as it has no front bumper for passy fender.

mark post as helpful recommend reputation points    Reply With Quote
Old 04-22-2010, 07:38 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #18 (permalink)
Banned Member
 

ramsack's Avatar
Car: Bicycle
Registered: Dec 2007
Tech Posts: 2,196
Photos: 4
Classifieds Rating: 3
Reputation: ramsack is pretty helpful and trustworthyramsack is pretty helpful and trustworthy
Send a message via AIM to ramsack
denso or whoever makes them rates them at 43.5 psi (3 bar) like all other injectors and manufacturers. doesn't it strike you odd that the 380 @ 42.7 psi calculate to the nearly same as 450s @ 36.3 psi? i have 2g 450s in my car, and my fuel pressure is about 42-44 base (fpr overrun), and 43.5 is what the 2g are rated at 450 for, and my car runs rich as shit because of that.

take a stock 1g, put a 43.5 regulator on it, and tune it somehow for added fuel, and you already have an upgraded fuel system.
Visit ramsack's homepage!  View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 04-22-2010, 07:49 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #19 (permalink)
Proven Member
 

natertater's Avatar
Registered: Jun 2008
Tech Posts: 232
Classifieds Rating: 5
Reputation: natertater is an unknown
Send a message via Yahoo to natertater
so if i take a 2g fpr and pop it on there, with evo8 injectors i will be fine for 18psi, i plan on getting ostrich and wideband shortly here. you can plug narrowband sim wire into ecu where normal nb went right? i have seen someone talk about it on here, but just making sure.

mark post as helpful recommend reputation points    Reply With Quote
Old 04-22-2010, 07:54 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #20 (permalink)
Banned Member
 

ramsack's Avatar
Car: Bicycle
Registered: Dec 2007
Tech Posts: 2,196
Photos: 4
Classifieds Rating: 3
Reputation: ramsack is pretty helpful and trustworthyramsack is pretty helpful and trustworthy
Send a message via AIM to ramsack
well if you're going that route i would get something like 680s. if you're getting an ostrich, you could try ds-map and not have to deal with a mafs at all.

my bad, a 450cc injector down to 36.3 psi will be 411cc. a 390cc down to 42.7 will be 386cc. i don't understand why there's a square root in the equation for that. so 550s for e85 is wrong. if 1g pressure was 43.5, then my calculations would be correct. 14.7 / 9.76 = 1.5, 1.5 * 450 is 675. a 680 injector @ 43.5 would be plenty since the 1g injector is really a 411cc. it wouldn't hurt to go even higher since you want 18psi of boost. also note that you shouldn't have problems controlling idle with big injectors because you are not trying to make huge injectors idle gasoline. you are making big injectors idle a fuel that injects more volume per air than gas, so in turn adding fuel across the board.
Visit ramsack's homepage!  View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Reply

Bookmarks

Thread Tools

 

» Recent DSM Photo
» Current Poll
How many times have you been to the Shootout?
1 - 39.86%
167 Votes
2-5 - 41.77%
175 Votes
6-10 - 10.50%
44 Votes
11-15 - 3.10%
13 Votes
16-20 - 4.77%
20 Votes
Total Votes: 419
You may not vote on this poll.
» Online Users: 842
237 members and 605 guests
Most users ever online was 1,704, 03-17-2008 at 09:11 PM.
DSMtuners Main Sections
DSM Forums
DSM Regional Forums
DSM Builds/Journals
DSM Articles
DSM Tech Guides
DSM Upgrade Paths
DSM Parts Reviews
DSM Vendor Reviews

DSM Classifieds
DSM Parts Guides
DSM Photos
DSM Videos
DSM Timeslips
DSM Dyno Sheets
Shirts & Apparel
DSMtuners Decals

Advertising Info
Our Sponsors
Site Rules
Terms of Service
Privacy Policy
Site FAQ
About Us
Contact Us

© 2014 DSMtuners.com - All Rights Reserved

DSMtuners is not affiliated with Diamond Star Motors. The Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, Mitsubishi Galant VR-4, and associated logos are trademarks of Diamond Star Motors, Mitsubishi Motors, and Chrysler Corporation. No, we do not hand out car sponsorships.

All times are GMT -7. The time now is 08:15 PM.


Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.

Search Engine Optimization by vBSEO 3.6.0