DSM Forums - NorCal Region DSM http://www.dsmtuners.com/forums/ Northern California and coastal areas en Sat, 21 Nov 2009 03:42:55 GMT vBulletin 60 http://www.dsmtuners.com/forums/images/misc/rss.jpg DSM Forums - NorCal Region DSM http://www.dsmtuners.com/forums/ Help me fill out the last few ECU numbers http://www.dsmtuners.com/forums/norcal-region-dsm/355122-help-me-fill-out-last-few-ecu-numbers.html Fri, 20 Nov 2009 17:14:04 GMT Some of you may know about my ECU cross reference list.

There are a couple of California ECU's that I've not seen and don't have any pictures of. I'd like to complete the list and here's where you can help.

If you have one of the following, please write down the E2T number under the part number on the top of the case. If you could take pictures of the top of the case and the board inside including the white edge connector that would be very helpful.
If you happend to have a EPROM version of the ECU so much the better. I'm like to verify the software version printed on the EPROM.

Here's what I need:
7/92-5/94 Turbo AWD MT - MD193295
7/92-5/94 Turbo AWD AT - MD193296
7/92-5/94 Turbo FWD MT - MD193293
7/92-5/94 Turbo FWD AT - MD193294 ]]> NorCal Region DSM steve http://www.dsmtuners.com/forums/norcal-region-dsm/355122-help-me-fill-out-last-few-ecu-numbers.html Mitsubishi Eclipse parts 2g DSM 18g T25 turbo FOR SALE http://www.dsmtuners.com/forums/norcal-region-dsm/354744-mitsubishi-eclipse-parts-2g-dsm-18g-t25-turbo-sale.html Mon, 16 Nov 2009 11:22:33 GMT I have various parts taken off my 1998 Mitsubishi Eclipse GST. They are listed below with sales pricing starting at $50 + shipping. Payments will go through cash local pick-up OR through Paypal. Located near Daly City, CA. PM me if you're interested. Parts are in like new condition to good condition.

- stock Mitsubishi T25 turbo. Turbo timed for most of it's life. A little movement for side to side shaft play that is within normal spec and no in/out shaft play. Turbo is in GREAT condition! Selling for $100 + shipping.

- stock 2g 1998 fog lights. This is for both lights. Working when it was taken off my car. $100 + shipping.

- Dejon Tool Upper Intercooler Pipe (UICP) is designed for GM Maft in blow thru setup and routed to stock side mount intercooler. Needs cleaning but overall in good condition. BOV flange setup for a Greddy Type S BOV. Selling for $90 + shipping.

- stock side mount intercooler (SMIC) in fair condition. Recommend cleaning before re-use. Selling for $50 + shipping

- Forced Performance 18g 6SL2 turbo with internal wastegate. If you want a turbo that can get you around 350whp with quick spool then this is the turbo for you! Bought this turbo brand new about a year and a half ago. Less than 2,000 miles on it. The wastegate arm/ flapper doesn't close all the way and gets stuck. The wastegate arm/flapper can probably be fixed or you can replace it easily. Or you could weld the internal wastegate shut and use a external wastegate. The turbo brand new is $799+tax, but I will let it go for $550 cash. This turbo has been turbo timed for the entire time it was on my car and there is no shaft play. This turbo is in great condition. Just the wastegate needs fixing. Selling for $550 + shipping

- stock 4G63T camshafts taken from my 1998 Mitsubishi Eclipse GST. In great condition! Selling for $150 + shipping for the set.

- stock heat shield for stock o2 housing on 2g Mitsubishi Eclipse. Selling for $50 + shipping.

- stock 4G63T valvesprings set. Selling for $100 + shipping

- stainless steel 2.5" recirculated o2 housing for 2g Eclipse. Received as a gift but don't need it. This is brand new! Selling for $60 + shipping

- cargo cover from 98 Eclipse. $50 + shipping ]]> NorCal Region DSM eclipseGSTud http://www.dsmtuners.com/forums/norcal-region-dsm/354744-mitsubishi-eclipse-parts-2g-dsm-18g-t25-turbo-sale.html <![CDATA[wtb> 14b turbo]]> http://www.dsmtuners.com/forums/norcal-region-dsm/354561-wtb-14b-turbo.html Sat, 14 Nov 2009 02:49:21 GMT bought one! thanks for the replys guys bought one! thanks for the replys guys ]]> NorCal Region DSM noss88 http://www.dsmtuners.com/forums/norcal-region-dsm/354561-wtb-14b-turbo.html <![CDATA[17" Motegi Rims... good tires for trade fairfield area]]> http://www.dsmtuners.com/forums/norcal-region-dsm/354558-17-motegi-rims-good-tires-trade-fairfield-area.html Sat, 14 Nov 2009 02:20:01 GMT hi i have 17" motegi's looking to trade for stock eclipse gst rims or some oems must have good tires because mine have alot of tread left... im in the fairfield area:thumb:

the marks in the middle of the rim is just dirt and a lil bit of oil... its not scratches though... all four rims have no scratches :thumb:
Attached Images
   
]]> NorCal Region DSM gst707 http://www.dsmtuners.com/forums/norcal-region-dsm/354558-17-motegi-rims-good-tires-trade-fairfield-area.html Interesting Website http://www.dsmtuners.com/forums/norcal-region-dsm/354214-interesting-website.html Mon, 09 Nov 2009 21:59:32 GMT What's cracking everyone. Now I was being bored and decided to share this site called Car Bibles. Pretty interesting and thought it might help people with certain questions with basics.

Aight everyone, check you all later on. Peace out for now

The Car Maintenance Bibles ]]> NorCal Region DSM EventsCo21XL http://www.dsmtuners.com/forums/norcal-region-dsm/354214-interesting-website.html <![CDATA[Fs/Ft 95-99 Eclipse Turbo C&R Radiator]]> http://www.dsmtuners.com/forums/norcal-region-dsm/354034-fs-ft-95-99-eclipse-turbo-c-r-radiator.html Sat, 07 Nov 2009 07:07:11 GMT Bought this brand new never got around to installing it. Besides I never drive my car on hot days or track it. So I thought someone might be interested in it, I have included a webpage that has and install and pics for reference. Sell out right for $210 shipped $230 Or trade for a Harmonic... Bought this brand new never got around to installing it. Besides I never drive my car on hot days or track it. So I thought someone might be interested in it, I have included a webpage that has and install and pics for reference.

Sell out right for $210 shipped $230

Or trade for a Harmonic FluiDampr 95-99 or Dynatek ignition(plus cash on my end)

C&R Radiator Install - Automotive Articles .com Magazine

Located Modesto, Ca
Email josatilio@netscape.net ]]> NorCal Region DSM spectergsx http://www.dsmtuners.com/forums/norcal-region-dsm/354034-fs-ft-95-99-eclipse-turbo-c-r-radiator.html F/S: 1997 Mitsubishi Eclipse GST 5 Speed http://www.dsmtuners.com/forums/norcal-region-dsm/353880-f-s-1997-mitsubishi-eclipse-gst-5-speed.html Thu, 05 Nov 2009 04:40:07 GMT Hey DSMtuners, here up I have my 1997 Eclipse GST Turbo 5 speed manual transmission. Car has 215,xxx miles on it. I had the car for little over two years and put in a lot of parts to keep it running as it should. (have receipts, records, logs, etc.) About two months ago, the car was involved... Hey DSMtuners, here up I have my 1997 Eclipse GST Turbo 5 speed manual transmission.

Car has 215,xxx miles on it. I had the car for little over two years and put in a lot of parts to keep it running as it should. (have receipts, records, logs, etc.)

About two months ago, the car was involved in a hit and run accident when it was parked in the street. I caught the guy and had his insurance pay me off for the damages. I purchased another car and this car has to go because I have no room/place for it.

Modifications:
-Autometer Phantom 30/30 boost gauge
-Autometer Phantom Short Sweep Oil pressure gauge
-OBX Dual gauge pods.
-Full bodied EMOTOR Coilover suspension. Adjustable Height, non-adjustable dampening, anodized red.
-Pioneer CD Deck player.
-Generic axle back muffler. (flat black)
-Revised 3rd Generation lifters/tappets. (operates very quietly.)
-Mitsubishi Lancer Evolution 8 rims

Highlights:
The engine is fine. Nothing involved with the engine or transmission was damaged in the accident. The timing belt, water pump, transmission, inner/outer tie rods with both bellow boots, control arms, radiator, starter, alternator, p/s and alternator belts, air filter, clutch, pressure plate, flywheel, pivot ball, clutch fork, clutch master cylinder, and a few other things were all changed during the duration of the two years of owning this vehicle.

Things that need to attention:
-The engine starts, but it starts rough.
-It burns oil because of old worn out valve seals.
-Passenger side window doesn't work.
-Both front axle boots are ripped.
-Front tires have about 20% tread left. Rear tires have about 45%, but one is flat due to the accident.
-Roof and top area of the quarter panel is faded/oxidized.
-In the accident, the guy that hit me damaged the driver side quarter panel leaving a fairly large dent. He damaged and bent the tire thus flattening the tire. He also damaged the whole rear driver side suspension components and thus leaving the car immobile. (please refer to pictures.)

So basically the whole rear end/crossmember of the car and driver side wheel needs to be replaced. It's a fairly easy repair if you know anything about wrenching. Parts are available for cheap at your local Pink N Pull or Pull your Part. The engine turns over and stays on. The clutch and transmission was replaced about 1 year ago and shifts as smooth as butter. (transmission was purchased from DSM_PWR)

Makes for a good project car or parts car.

I put a lot of work into this thing from day one. It's a shame that my car was hit out of the cars in the neighborhood it was parked in. I love this car, but I don't have the money to get her mobile again.

Asking 1100 or best offer. You must provide and must come with a tow or trailer to take the car home.

Pictures: 11/4/09 (click on the link) and in my gallery as well.
ImageShack -

F/S: 1997 Mitsubishi Eclipse GST 5 Speed

You can reach my @ 408 431 9977. ]]> NorCal Region DSM meliketoball http://www.dsmtuners.com/forums/norcal-region-dsm/353880-f-s-1997-mitsubishi-eclipse-gst-5-speed.html FS: 2G-A car cover custom fitment http://www.dsmtuners.com/forums/norcal-region-dsm/353830-fs-2g-car-cover-custom-fitment.html Wed, 04 Nov 2009 18:41:27 GMT I have a car cover it is custom made for 95-96 eclipse. It may fit other 2G DSM depending on your car. It fits like a glove and has grommets to tie down also.
Multiple layers very high quality.
I bought it for $200+ new, it's either coverking or covercraft
Similar to this
http://www.dsmtuners.com/forums/appe...se-review.html

Looking for $100 shipped or $80 picked up.
Just think how much is a new paint job.. protect your car if it's sitting outside waiting for parts to run again :) ]]> NorCal Region DSM 95GST http://www.dsmtuners.com/forums/norcal-region-dsm/353830-fs-2g-car-cover-custom-fitment.html 2G performance parts for sale.. http://www.dsmtuners.com/forums/norcal-region-dsm/353759-2g-performance-parts-sale.html Tue, 03 Nov 2009 20:02:03 GMT 2G DSM Radiator great condition very low miles. $40

95 Mitsu Eclipse factory shop manual. Includes 2 books, mechanical and electrical. Must have for 2G owners
$60.. will throw in chilton's manual for free also.

test pipe, for 2G AWD, with gaskets. 2.5" $20

RRE multi ply metal exhaust manifold gasket. NEW never used. really good gasket and won't leak. (I had another one in my car)

2G 95-96 fog lights with brackets. $20

2G fuel rail and feed hose from fuel filter. No banjo bolt include $10

Ported EVO3 O2 housing, massively hogged out to true 2.5", turbine side about 2.4" and 2". Ported by the best porter at Forced Performance. Then it has been high temp coated for best durability and keep the temperature inside, no heat shield is needed.
$80






]]> NorCal Region DSM 95GST http://www.dsmtuners.com/forums/norcal-region-dsm/353759-2g-performance-parts-sale.html anybody have an extra stock GST muffler? http://www.dsmtuners.com/forums/norcal-region-dsm/353610-anybody-have-extra-stock-gst-muffler.html Sun, 01 Nov 2009 20:00:36 GMT looking for a GST or a Spyder dual-tip muffler for my car. been searching through craigslist and only found one but dude wants $100 WTF. i was like wow. also, would a gsx muffler bolt on or weld onto a regular gs? Thanks looking for a GST or a Spyder dual-tip muffler for my car. been searching through craigslist and only found one but dude wants $100 WTF. i was like wow. also, would a gsx muffler bolt on or weld onto a regular gs? Thanks ]]> NorCal Region DSM dispinoygotgame http://www.dsmtuners.com/forums/norcal-region-dsm/353610-anybody-have-extra-stock-gst-muffler.html need help...spring http://www.dsmtuners.com/forums/norcal-region-dsm/353600-need-help-spring.html Sun, 01 Nov 2009 18:39:13 GMT yesterday i hit a real hard dip and my back right sleeve and my spring fell to the bottom..so do anyone has a stock spring i can buy im not trying to buy all four..if anyone can help i would appreciate it... yesterday i hit a real hard dip and my back right sleeve and my spring fell to the bottom..so do anyone has a stock spring i can buy im not trying to buy all four..if anyone can help i would appreciate it... ]]> NorCal Region DSM lizoyd18 http://www.dsmtuners.com/forums/norcal-region-dsm/353600-need-help-spring.html 95 GS-T 6 bolt, LSD, DSMLink lots of extras http://www.dsmtuners.com/forums/norcal-region-dsm/353108-95-gs-t-6-bolt-lsd-dsmlink-lots-extras.html Mon, 26 Oct 2009 17:29:01 GMT Thanks Thanks ]]> NorCal Region DSM 95GST http://www.dsmtuners.com/forums/norcal-region-dsm/353108-95-gs-t-6-bolt-lsd-dsmlink-lots-extras.html FS: 2g Stillen front bumper http://www.dsmtuners.com/forums/norcal-region-dsm/352990-fs-2g-stillen-front-bumper.html Sun, 25 Oct 2009 07:22:12 GMT Well I have my old stillen front bumper for sale. Its polyurethane and has been modded to fit a fmic.

Asking $150obo

97 Eclipse

Stillen Front bumper, FMIC, Apexi Springs ]]> NorCal Region DSM Killa_dsm http://www.dsmtuners.com/forums/norcal-region-dsm/352990-fs-2g-stillen-front-bumper.html car parts http://www.dsmtuners.com/forums/norcal-region-dsm/352953-car-parts.html Sat, 24 Oct 2009 21:44:03 GMT AEM wideband. under 100 miles $150 firm 97 98 Talon high rise spoiler $50 firm. Weapon R racing seat bracket/frame. DR/PASS. $50 firm coil on plug $ 100 small 16g trade for 14b + $100 AEM wideband. under 100 miles $150 firm

97 98 Talon high rise spoiler $50 firm.

Weapon R racing seat bracket/frame. DR/PASS. $50 firm

coil on plug $ 100

small 16g trade for 14b + $100

20 intripid coils with pig tail $5 each or $80 for all.

1ga black hood $20

1ga side skirts $20

1ga wrap around spoiler $20


Call or text 408 667 1109 Nico ]]> NorCal Region DSM 93_tsi_fwd http://www.dsmtuners.com/forums/norcal-region-dsm/352953-car-parts.html rear disc brakes http://www.dsmtuners.com/forums/norcal-region-dsm/352933-rear-disc-brakes.html Sat, 24 Oct 2009 18:00:19 GMT so i have some rear disc brakes to replace my drums on my 96 talon but i am new to the sacramento area could anyone recomend a shop that would help me with this? i have trouble making it to the monthly meets. otherwise that is where i would ask this question. i guess a person with the tools would... so i have some rear disc brakes to replace my drums on my 96 talon but i am new to the sacramento area could anyone recomend a shop that would help me with this? i have trouble making it to the monthly meets. otherwise that is where i would ask this question. i guess a person with the tools would be able to help me with this as well. what should i pay for this job. like two hours? 200$
i still have to get rotors but maybe before christmas?
stuart ]]> NorCal Region DSM studabaker http://www.dsmtuners.com/forums/norcal-region-dsm/352933-rear-disc-brakes.html